12
29.
Wrap the Low Cable (47) under a 90mm Pulley
(38).
Attach the Pulley and a pair of Pulley
Covers (44) inside the indicated bracket on the
Front Base (1) with an M10 x 53mm Bolt (61) and
an M10 Nylon Locknut (71).
Make sure the small
tabs on the Pulley Covers are on top.
28. Wrap the Low Cable (47) over a 90mm Pulley
(38). Attach the Pulley and a pair of Pulley
Covers (44) to the second set of holes from the
bottom of the two Pulley Plates (36) with an M10
x 53mm Bolt (61) and an M10 Nylon Locknut
(71). Make sure that the large tabs on the
Pulley Covers are on top.
61
36
38
44
44
47
71
28
38
61
47
44
44
1
71
29
Large Tab
Small Tab
25. Attach the Short Cable (83) to the Large “U”-
bracket (82) with an M8 Washer (62) and an M8
Nylon Locknut (70).
Do not completely tighten
the Locknut; it should be tightened so that
only two threads of the Cable show past the
Locknut, as shown in the inset drawing.
82
83
70
62
25
9
12. Press two 40mm x 50mm Inner Caps (23) into
the ends of the Leg Lever (4).
Lubricate an M10 x 65mm Bolt (81) with grease.
Attach the Leg Lever (4) to the Seat Upright (73)
with the Bolt and an M10 Nylon Locknut (71). Do
not overtighten the Locknut; the Leg Lever
must be able to pivot easily.
11. Lubricate an M10 x 80mm Allen Head Bolt (50)
and both sides of two Plastic Washers (55) with
grease. Attach the Right Butterfly Arm (11) to the
Butterfly Frame (9) with the Bolt, the two Plastic
Washers, two Butterfly Caps (54), two M10
Washers (26), and an M10 Nylon Locknut (71).
Do not overtighten the Locknut; the Butterfly
Arm must be able to pivot easily
. Make sure
the indented sides of the Plastic Washers fit
over the welded bushing in the Butterfly Arm.
Repeat this step with the Left Butterfly Arm (10).
9
Lubricate
Welded
Bushing
Lubricate
1
1
71
55
55
54
54
26
26
50
10
1
1
4
Lubricate
81
71
23
23
73
12
13. Locate the Butterfly Cable (46). Attach the
Cable to the indicated Pivot Bracket (48) with an
M8 x 27mm Shoulder Bolt (63) and an M8 Nylon
Locknut (70).
70
46
48
63
13
CABLE ASSEMBLY
14.
Wrap the Butterfly Cable (46) over a “V”-pulley
(39).
Attach the “V”-pulley and a Long Cable
T
rap
(40) to the bracket on the Front Upright (6) with
an M10 x 57mm Bolt (69) and an M10 Nylon
Locknut (71).
Be sure the Cable T
rap is turned
to hold the Cable in the groove of the Pulley
.
69
46
40
71
6
39
14
26. Locate the Low Cable (47). Route the Cable
through the cage and under a 90mm Pulley (38).
Attach the Pulley and a pair of Pulley Covers (44)
inside the indicated bracket on the Centre Base
(2) with an M10 x 53mm Bolt (61) and an M10
Nylon Locknut (71). Make sure that the large
tabs on the Pulley Covers are on top.
38
44
44
2
61
47
71
Cage
Large Tab
26
27. Wrap the Cable under a 90mm Pulley (38). Attach
the Pulley and a pair of Pulley Covers (44) inside
the indicated bracket on the Centre Base (2) with
an M10 x 53mm Bolt (61) and an M10 Nylon
Locknut (71). Make sure that the large tabs on
the Pulley Covers are on top.
61
38
44
44
2
71
27
Large Tab
83
70
82
(20 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals