13
32. Route the Low Cable (47) through the Seat
Upright (73) and under a 90mm Pulley (38).
Attach the Pulley and a pair of Pulley Covers (44)
inside the Seat Upright with an M10 x 68mm Bolt
(59), two M10 Washers (26), two 8mm Spacer
(51), and an M10 Nylon Locknut (71). Make sure
the small tabs on the Pulley Covers are on the
bottom.
See the inset drawing. Attach the end of the
Low Cable (47) to the Leg Lever (4) with an M8 x
27mm Shoulder Bolt (63) and an M8 Nylon
Locknut (70).
73
51
51
38
26
26
59
47
44
44
71
32
33.
Orient the Seat (16) as shown.
Attach the Seat to
the Seat Frame (5) with an M6 x 65mm Screw
(65), an M6 Washer (35), and two M6 x 15mm
Screws (66).
16
35
65
5
66
W
ide
End
33
SEAT ASSEMBLY
4
47
63
70
8. Attach the Seat Frame (5) to the Front Upright (6)
with an M10 x 70mm Bolt (58), an M10 x 77mm
Bolt (60), three M10 W
ashers (26), and two M10
Nylon Locknuts (71).
Don’t over tighten the
Locknut on the M10 x 77mm Bolt; a cable will
be attached to this bolt in step 23.
Attach the Seat Frame (5) to the Seat Upright
(73) with two M10 x 70mm Bolts (58), two M10
Washers (26), and two M10 Nylon Locknuts (71).
Tighten the M10 Nylon Locknuts (71) used in
steps 1–8.
8
26
26
26
73
6
5
26
71
58
60
58
8
71
9. Press a 50mm Square Inner Cap (22) into the
Butterfly Frame (9).
Lubricate the M10 x 77mm Bolt (60) with grease.
Attach the Butterfly Frame (9) to the Top Frame
(8) with the Bolt and an M10 Nylon Locknut (71).
Do not overtighten the Locknut; the Butterfly
Frame must be able to pivot easily.
71
9
22
Lubricate
60
8
9
ARM ASSEMBLY
10. Press a 40mm x 50mm Inner Cap (23) into the
indicated end of the Right Butterfly Arm (11). Wet
the bottom end of the Arm with soapy water. Slide
a Large Foam Pad (19) onto the Arm.
Attach a Pivot Bracket (48) to the Right Butterfly
Arm (11) with an M10 x 53mm Bolt (61) and an
M10 Nylon Locknut (71). Do not overtighten the
Locknut; the Pivot Bracket must be able to
pivot easily.
Slide a Foam Grip (76) onto a Butterfly Handle
(12). Press a 31mm Round Inner Cap (24) into the
Butterfly Handle. Attach the Butterfly Handle to the
Right Butterfly
Arm (11) with two M8 x 15mm Allen
Head Bolts (64) and two M8 Washers (62).
Slide the Large Foam Pad (19) down so that the
bottom of the Foam Pad is even with the bottom
of the Right Butterfly Arm (11).
Repeat this step with the Left Butterfly
Arm (10).
19
76
12
23
11
71
64
64
61
48
10
62
62
24
10
Small
Tab
30. Wrap the Low Cable (47) over a 90mm Pulley
(38). Attach the Pulley and a pair of Pulley
Covers (44) to the Large “U”-bracket (82) with an
M10 x 53mm Bolt (61) and an M10 Nylon Locknut
(71).
Make sure the small tabs on the Pulley
Covers are on the bottom.
31. Wrap the Low Cable (47) under a 90mm Pulley
(38). Attach the Pulley and a pair of Pulley
Covers (44) inside the Front Upright (6) with an
M10 x 68mm Bolt (59), two M10 Washers (26),
two 8mm Spacer (51), and an M10 Nylon Locknut
(71).
Make sure the large tabs on the Pulley
Covers are oriented as shown.
61
82
38
47
44
44
71
30
6
51
51
38
26
26
59
47
44
44
71
31
Small Tab
Large Tab
(20 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals