11
20. Wrap the High Cable (45) under a 90mm Pulley
(38). Attach the Pulley and a pair of Pulley
Covers (44) to the second set of holes from the
top of the two Pulley Plates (36) with an M10 x
53mm Bolt (61) and an M10 Nylon Locknut (71).
Make sure that the small tabs on the Pulley
Covers are on top.
44
38
45
Small
Tabs
36
36
61
71
44
20
21. Wrap the High Cable (45) over a 90mm Pulley
(38). Attach the Pulley inside the Top Frame (8)
with an M10 x 68mm Bolt (59), two M10 Washers
(26), two 13mm Spacers (34), and an M10 Nylon
Locknut (71).
38
59
45
34
34
8
26
26
71
21
22. Attach the High Cable (45) to the “U”-bracket (77)
with an M8 Washer (62), and an M8 Nylon
Locknut (70). Do not completely tighten the
Locknut; it should be tightened so that only
two threads of the Cable show past the
Locknut, as shown in the inset drawing.
Attach the “U”-bracket (77) to the Weight Tube
(20) with an M8 x 43mm Bolt (56) and an M8
Nylon Locknut (70). Do not overtighten the
Locknut; the Weight Tube must be able to
pivot easily.
23. Locate the Short Cable (83). Remove the M10
Nylon Locknut (71) from the indicated M10 x
77mm Bolt (60). Attach the Cable to the Bolt with
the Locknut.
45
45
20
56
70
70
70
62
77
77
22
6
83
60
71
23
44
44
37
71
83
61
24
Large Tab
10
16. Wrap the Butterfly Cable (46) over a “V”-pulley
(39). Attach the “V”-pulley and a Long Cable Trap
(40) to the bracket on the Front Upright (6) with
an M10 x 57mm Bolt (69) and an M10 Nylon
Locknut (71).
Make sure the Cable Trap is
turned to hold the Cable in the groove of the
Pulley.
15. Wrap the Butterfly Cable (46) under a 90mm
Pulley (38). Attach the Pulley and a pair of Pulley
Covers (44) to the Double “U”-bracket (37) with
an M10 x 53mm Bolt (61) and an M10 Nylon
Locknut (71).
Make sure the small tabs on the
Pulley Covers are on top.
61
37
38
71
46
44
44
15
6
39
46
69
71
40
16
Small
Tabs
17. Attach the Butterfly Cable (46) to the indicated
Pivot Bracket (48) with an M8 x 27mm Shoulder
Bolt (63) and an M8 Nylon Locknut (70).
70
46
63
48
17
18. Locate the High Cable (45). Route the bolt end
of the Cable up through the Top Frame (8) and
over a 90mm Pulley (38). Attach the Pulley inside
the Top Frame with an M10 x 68mm Bolt (59),
two M10 W
ashers (26), two 13mm Spacers (34),
and an M10 Nylon Locknut (71).
8
45
34
34
38
71
26
26
59
18
19.
Wrap the High Cable (45) over a 90mm Pulley
(38).
Attach the Pulley inside the
T
op Frame (8)
with an M10 x 68mm Bolt (59), two M10 Washers
(26), two 13mm Spacers (34), and an M10 Nylon
Locknut (71).
8
45
34
26
38
71
34
26
59
19
24.
Wrap the Short Cable (83) over a 90mm Pulley
(38).
Attach the Pulley and a pair of Pulley
Covers (44) to the Double “U”-bracket (37) with
an M10 x 53mm Bolt (61) and an M10 Nylon
Locknut (71).
Make sure that the large tabs on
the Pulley Covers are on top.
(20 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals