14
37.
Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in
ADJUSTMENTS, beginning on the next page.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly
, find and correct the problem.
IMPORT
ANT
: If
the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE
DIAGRAM on page 17 of this manual for proper cable routing. If there is any slack in the cables, you
will need to remove it by tightening the cables; see TIGHTENING THE CABLES on page 16.
7
6. Press two 50mm Square Inner Caps (22) into the
end of the Top Frame (8).
Attach the Top Frame (8) to the Front Upright (6)
with two M10 x 70mm Bolts (58), the 90mm
Space Support Plate (21), and two M10 Nylon
Locknuts (71).
Attach the Weight Guides (31) to the Top Frame
(8) with an M10 x 155mm Bolt (67), two M10
Washers (26), and an M10 Nylon Locknut (71).
Do not tighten the M10 Nylon Locknuts (71) yet.
31
22
22
71
71
6
71
26
26
21
8
58
67
6
5. Slide the nine Weights (7) onto the Weight
Guides (31). Make sure the pin grooves are on
the indicated side.
Press the W
eight Tube Bumper (14) into the
Weight Tube (20). Insert the Weight Tube into the
stack of Weights (7).
Lubricate the indicated holes in the Top Weight
(30) with grease. Slide the Top Weight onto the
Weight Guides (31).
Make sure the pin on the
Weight Tube (20) rests in the groove on the
bottom of the Top Weight.
Insert the Weight Pin (13) into the stack of
Weights (7).
13
14
20
31
30
Pin
Pin
Grooves
Lubricate
7
5
36. Insert the two Locking Pins (53) into the Butterfly
Frame (9). Attach the tether on the Pins to the
Butterfly Frame with the M4 x 12mm Screw (68).
9
53
53
68
36
7. Press a 50mm Square Inner Cap (22) into the
Seat Upright (73).
Attach the Bumper (25) to the
Seat Upright with an M4 x 20mm Screw (72) and
an M5 Washer (75).
Attach the Seat Upright (73) to the Front Base (1)
with the two indicated M10 x 65mm Carriage
Bolts (57) and two M10 Nylon Locknuts (71).
Do
not tighten the Locknuts yet.
7
72
25
75
71
71
1
73
22
57
34. Attach the Backrest (15) to the Front Upright (6)
with two M6 x 65mm Screws (65), and two M6
W
ashers (35).
35. Press two 19mm Round Inner Caps (27) into the
ends of a Pad Tube (17). Slide the Pad Tube
through the hole in the Leg Lever (4). Slide two
Foam Pads (18) onto the ends of the Pad
Tube.
Repeat this step with the other Pad Tube (17)
and the Seat Upright (73).
6
35
65
65
15
17
4
73
27
27
18
18
17
35
34
35
(20 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals