Weider WESY19511 User Manual

USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or find there aremi

1015. Route the Long Cable (23) around the “V”-Pulley(6) on the Right Arm (48). Be sure that theCable is in the groove of the “V”-Pulley andthat the L

1119. Locate the Short Cable (58). Lay the ShortCable in the bracket on the Base (4). Attach the 90mm Pulley (15) to the bracket with an M10 x45mm Bol

1222. Route the Short Cable (58) around the 90mmPulley (15) attached to the upper hole in the FrontUpright (42). See the inset drawing. Be surethat th

24. Attach the Long Cable (23) to the Small “U”-Bracket (67) with an M8 Nylon Locknut (3) and anM8 Washer (8). See the inset drawing. Do notovertighte

1426. Press a 38mm Square Inner Cap (32) into theSeat Frame (36).Insert the M6 x 50mm Carriage Bolt (38) into thecenter hole in the Seat Plate (37). A

1529. Press a 19mm Round Inner Cap (34) into eachend of both Pad Tubes (28). Insert one Pad Tube (28) into the Seat Frame(36). Slide a Foam Pad (30) o

16ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

17ATTACHING THE LEG LEVER TO THE LOWPULLEY STATIONTo use the Leg Lever (29), the seat must be attachedto the front upright (see ATTACHING AND REMOV-IN

18WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEYPLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)Top 20 10 15 14 2 4145 22 36 28 54270 33 54

19TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. Theweight sys

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw

21NOTES

22Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY19511 R0802B1 2 M8 x 63mm C

231111885527801544157723272144213616035615123575821355114192651256463769213341276515714110433216507427506216970697047484445444513403837183228303410224

ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6

REMOVE THIS PART IDENTIFICATIONCHART FROM THE MANUALThis chart is provided to help you identify the small parts used in assembly. Important: Some part

M8 Nylon Locknut (3)M6 Washer (10)M8 Washer (8)M10 Washer (9)M6 x 65mm Screw (43)M8 x 45mm Bolt (72)M10 Nylon Locknut (21)M6 x 50mm Screw (24)M8 x 70m

25mm Retainer (69)M10 x 90mm Bolt (77)M10 x 45mm Bolt (80)M10 x 50mm Bolt (12)M10 x 80mm Bolt (16)M10 x 60mm Bolt (7)M10 x 95mm Bolt (71)M10 x 195mm B

25mm Round Inner Cap (49)25mm Round Cover Cap (70)13mm x 19mm Spacer (61)38mm Square Inner Cap (32)38mm Square Inner Cap (44)50mm Square Inner Cap (27

3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.IMPORTANT PRECAUTIONSWARNING: B

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 37 in. Length: 48 in. Foot PlateLow Pulley StationHigh Pulley StationLeft SideRight SideLa

5156High Side of Bracket3551511412741. Before beginning assembly, be sure that youhave read and understand the information inthe box above.Press a 50m

62. Slide the Front Upright (42) onto the M8 x 63mmCarriage Bolts (1) in the Base (4). Hand tightenan M8 Nylon Locknut (3) onto each Carriage Bolt.Do

75. Press the Weight Tube Bumper (64) into the endof the Weight Tube (63). Insert the Weight Tubeinto the stack of Weights (25). Be sure that thepins

88. Press a 38mm Square Inner Cap (44) into the topof a Press Arm (46). Press a 25mm Round InnerCap (49) into each end of the handle on thePress Arm.

911. During steps 11 through 24, refer to the CABLEDIAGRAM on page 20 of this manual to verifyproper cable routing. Before beginning this sec-tion, id