¨USERÕSMANUALModel No. WESY81081Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRea
1014. Locate and open the parts bag labeled ÒCABLEASSEMBLY AND PULLEYS.Ó For Cable identifica-tion and routing during steps 14Ð28, refer to theCable D
1117. Move to the other side of the unit. Wrap the ShortCable (9) around a 3 1/2Ó Pulley (35) in the directionshown.Attach the 3 1/2Ó Pulley (35) and
1220. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)in the direction shown. Attach the 3 1/2Ó Pulley (35) tothe front bracket (M) underneath the
1325. Thread the Long Cable (2) through the Press Frame(12). Wrap the Long Cable around a 3 1/2Ó Pulley(35) in the direction shown. Attach the Pulley
1428. Wrap the Long Cable (2) around a 3 1/2Ó Pulley (35)in the direction shown. Attach the Pulley to the FrontUpright (42) with a 3/8Ó x 3 1/2Ó Bolt
1531. Press two 3/4Ó Round Inner Caps (34) into each PadTube (28). Insert one Pad Tube into the Seat Frame (36). Slide aFoam Pad (30) onto each end of
16Cable DiagramThe Cable Diagram below shows the proper routing of the Short Cable (9) and the Long Cable (2). The numbersshow the correct route for e
Attaching the Lat Bar, Row Bar or Handle tothe High Pulley StationAttach the Lat Bar (76) to the Short Cable (9) with aCable Clip (73). For some exerc
18Press Butterfly High Leg LowWeight Arm Arm Pulley Lever PulleyPlates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)Top 12 46 19 21 151 40 70 33 37 332 62 97 4
19Tightening the CablesWoven cable, the type of cable used on the home gymsystem, can stretch slightly when it is first used. If there isslack in the
2Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
603131353557343430304433283034283034812282713817371380332936958532316256426747375194545212134431562663563154847277777115856535318615353395515114528531
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. 1 1 Top Frame2 1 Long Cable3 2 1Ó Round Cover Cap4 4
1" Retainer (4)1/4" Flat Washer (81)3/8" x 2" Bolt (62)3/8" x 3 1/2" Bolt (54)Cable Clip (73)3/8" x 3 1/4" Bol
5/16" x 1 1/2" Bolt (61)1/4" x 2" Bolt (71)1/4" x 2" Carriage Bolt (38)1/4" x 2 1/2" Screw (43)5/16" x 2
1" Round Inner Cap (49)1" Round Cover Cap (3)3/4" Round Inner Cap (34)5/16" x 2" Eyebolt (44)1 1/2" Square Inner Cap (33
Ordering Replacement PartsTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
3WARNING: Before beginning this or any exercise program, consult your physician. This is especiallyimportant for persons over the age of 35 or persons
4ASSEMBLED DIMENSIONS: Height: 77 in.Width: 38 in. Length: 61 in. Low PulleyStationFoot PlateRow BarHigh Pulley StationLeg LeverButterfly ArmButterfly
5Note: This introduction will save you moretime than it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h
61. Before beginning assembly, make sure you haveread and understood the information on page 5.Locate and open the parts bag labeled ÒFRAMEASSEMBLY.ÓP
74. Set four Weight Bumpers (19) onto the Base (8) andalign them with the indicated holes.Insert both Weight Guides (23) through the WeightBumpers (1
87. Slide two 5/16Ó Flat Washers (56) onto two 5/16Ó x 1 3/4Ó Bolts (58).Align the holes in the bracket on the Top Frame (1)with the holes in the Rear
911. Press a 2Ó Square Inner Cap (21) into the top end ofeach Press Arm (46). Press a 1Ó Round Inner Cap (49) into the indicatedhole on each Press Arm
Comments to this Manuals