USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if parts aremissi
1014. Open the parts bag labeled “ARM ASSEMBLY.”Press three 1 1/2” x 2” Inner Caps (21) into the LegLever (10).Lubricate a 3/8” x 2 1/2” Bolt (18) wit
18.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Lubricate the 3/8” x 7” Bolt (30) with grease. Attachthe Swivel Cage (76) to t
1220. Remove the preattached 3 1/2” Pulleys (78) fromthe Small Pulley Plates (31).Wrap the Swivel High Cable (74) over a 3 1/2”Pulley (78). Attach the
1324. Remove the preattached 3 1/2” Pulleys (78) fromthe Offset Double “U”-bracket (61).Wrap the Swivel Cable (17) around a 3 1/2” Pulley(78). Attach
1429. Wrap the Lat Cable (88) around a 3 1/2” Pulley(78). Attach the Pulley and a Long Cable Trap (102)to the Top Frame (6) with a 3/8” x 1 3/4” Bolt
153536383734. Remove the preattached 3 1/2” Pulleys (78) fromthe Double “U”-bracket (62).Wrap the Butterfly Cable (69) under a 3 1/2” Pulley(78). Atta
1641. Remove the preattached 3 1/2” Pulley (notshown) from the “U”-bracket (64).Attach the end of the Leg Lever Cable (75) to the“U”-bracket (64) with
1745. Wrap the Swivel Low Cable (72) under a 3 1/2”Pulley (78). Attach the Pulley to the indicated brack-et on the Long Base (120) with a 3/8” x 1 3/4
1849. Wrap the Swivel Low Cable (72) over a 3 1/2”Pulley (78). Attach the Pulley and a Cable Trap (68)between the lower set of holes in the “U”-bracke
1953. Wrap the Squat Cable (73) under a 3 1/2” Pulley(78). Attach the Pulley and a Cable Trap (68) to thesecond set of holes from the top in the indic
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2057. Press two 3/4” x 1 1/2” Inner Caps (116) and a 1 1/4”Square Inner Cap (117) into the Seat Bracket (11). Attach the Seat (16) to the Seat Bracket
216161. Turn the Squat Backrest (35) so that the four screwholes are closer to the bottom of the SquatBackrest than the top. Attach the Squat Backrest
22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t
23ADJUSTING THE SQUAT ARM, SEAT, ORBUTTERFLY BACKRESTTo adjust the height of the Squat Arm (32), first turnthe Adjustment Knob (115) on the Squat Brac
HIGH PULLEY(lbs.)1425384861688096101112122LOW PULLEY(lbs.)1425364460708091104111122LEGLEVER(lbs.)2235536791111122148160184190BUTTERFLYARM(lbs.)1726364
25TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately. The weight sys
26CABLE DIAGRAMSThe cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-grams on this page and
27Leg LeverCable (75)Swivel LowCable (72)113245679234123458Swivel Cable (17)
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
Note: Assembly is divided into four stages: 1) frame assembly, 2) armassembly, 3) cable assembly, and 4) seat assembly. The hardware foreach stage is
IMPORTANT PRECAUTIONS31. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibil
Cable Clip (83)3 1/2" Pulley (78)(Not shown to scale)"V" Pulley (55)(Not shown to scale)4 1/2" Pulley (119)(Not shown to scale)3/8
3/8" x 2" Bolt (100)3/8" x 1 3/4" Bolt (93)#10 x 1" Screw (14)3/8" x 2 1/2" Bolt (18)5/16" x 2 3/4" Bolt
1 1/4" Square Inner Cap (117)1" Round Inner Cap (29)1 1/2" x 2” Inner Cap (21)2" Square Inner Cap (105)1 1/2" Square Inner Ca
81REMOVE THIS PART LIST/EXPLODED DRAWINGFROM THE MANUAL.SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
PART LIST—Model No. WESY39522 R1202ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 1/2” Washer2
465732891011131516109109191920202121202123242526272728292928323333111111353738393940404042424343474544454448484950501141141141145252555556575757585454
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 81 in.Width: 96 in. Length: 57 in. Squat Knee RestLow Pulley StationHigh Pulley StationLat BarSwivel Ca
5ASSEMBLYMake sure that you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mal
1.Locate and open the parts bags labeled “FRAMEASSEMBLY 1” and “FRAME ASSEMBLY 2.”Press a 2” Square Inner Cap (105) into the openend of the Long Base
4. Press a 1 1/2” Square Inner Cap (67) into theUpright Extension (12).Attach the Upright Extension (12) to the ButterflyUpright (3) with two 5/16” x
87. Press a 2” x 3” Inner Cap (58) into the top of theSquat Upright (4). Slide the Squat Upright onto thetwo indicated 5/16” x 2 1/2” Carriage Bolts (
99. Attach a Roller (39) and two 5/16” Washers (90)between the indicated set of holes in the SquatSlider (38) with a 5/16” x 3 1/2” Bolt (94), two 5/1
Comments to this Manuals