USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if parts aremissi
1014. Open the parts bag labeled “ARM ASSEMBLY.”Press three 40mm x 50mm Inner Caps (21) into theLeg Lever (10).Lubricate an M10 x 65mm Bolt (18) with
18.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Lubricate the M10 x 165mm Bolt (30) with grease.Attach the Swivel Cage (76) to
1220. Remove the preattached 90mm Pulleys (78)from the Small Pulley Plates (31).Wrap the Swivel High Cable (74) over a 90mmPulley (78). Attach the Pul
1324. Remove the preattached 90mm Pulleys (78)from the Offset Double “U”-bracket (61).Wrap the Swivel Cable (17) around a 90mm Pulley(78). Attach the
1429. Wrap the Lat Cable (88) around a 90mm Pulley(78). Attach the Pulley and a Long Cable Trap (102)to the Top Frame (6) with an M10 x 50mm Bolt(100)
153536383734. Remove the preattached 90mm Pulleys (78)from the Double “U”-bracket (62).Wrap the Butterfly Cable (69) under a 90mm Pulley(78). Attach t
1641. Remove the preattached 90mm Pulley (notshown) from the “U”-bracket (64).Attach the end of the Leg Lever Cable (75) to the“U”-bracket (64) with a
1745. Wrap the Swivel Low Cable (72) under a 90mmPulley (78). Attach the Pulley to the indicated brack-et on the Long Base (101) with an M10 x 45mmBol
1849. Wrap the Swivel Low Cable (72) over a 90mmPulley (78). Attach the Pulley and a Cable Trap (68)between the lower set of holes in the “U”-bracket(
1953. Wrap the Squat Cable (73) under a 90mm Pulley(78). Attach the Pulley and a Cable Trap (68) to thesecond set of holes from the top in the indicat
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2057. Press two 20mm x 40mm Inner Caps (116) and a25mm x 40mm Square Inner Cap (117) into theSeat Bracket (11). Attach the Seat (16) to the Seat Brack
216161. Turn the Squat Backrest (35) so that the four screwholes are closer to the bottom of the SquatBackrest than the top. Attach the Squat Backrest
22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t
23ADJUSTING THE SQUAT ARM, SEAT, ORBUTTERFLY BACKRESTTo adjust the height of the Squat Arm (32), first turnthe Adjustment Knob (115) on the Squat Brac
HIGH PULLEY(lbs.)1425384861688096101112122LOW PULLEY(lbs.)1425364460708091104111122LEGLEVER(lbs.)2235536791111122148160184190BUTTERFLYARM(lbs.)1726364
25TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately. The weight sys
26CABLE DIAGRAMSThe cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-grams on this page and
27Leg LeverCable (75)Swivel LowCable (72)113245679234123458Swivel Cable (17)
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
Note: Assembly is divided into four stages: 1) frame assembly, 2) armassembly, 3) cable assembly, and 4) seat assembly. The hardware foreach stage is
IMPORTANT PRECAUTIONS31. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibil
Cable Clip (83)90mm Pulley (78)(Not shown to scale)"V"-pulley (55)(Not shown to scale)115mm Pulley (119)(Not shown to scale)M10 Nylon Locknu
M10 x 20mm Bolt (86)M10 x 60mm Bolt (59)M10 x 70mm Bolt (85)M10 x 95mm Bolt (92)M10 x 45mm Bolt (93)M10 x 85mm Bolt (96)M10 x 165mm Bolt (30)M10 x 50m
50mm x 75mm Inner Cap (58)40mm x 50mm Inner Cap (21)25mm Round Inner Cap (29)50mm x 70mm Inner Cap (95)38mm Square Inner Cap (67)50mm Square Inner Cap
81REMOVE THIS PART LIST/EXPLODED DRAWINGFROM THE MANUAL.SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
PART LIST—Model No. WESY39523 R0103ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 50mm Washer2
465732891011131516109109191920202121202123242526272728292928323333111111353738393940404042424343474544454448484950501141141141145252555556575757585454
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 81 in.Width: 96 in. Length: 57 in. Squat Knee RestLow Pulley StationHigh Pulley StationLat BarSwivel Ca
5ASSEMBLYMake sure that you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mal
1.Locate and open the parts bags labeled “FRAMEASSEMBLY 1” and “FRAME ASSEMBLY 2.”See the inset drawing. Attach the Base Cap (24)to the Short Base (2)
4. Press a 38mm Square Inner Cap (67) into theUpright Extension (12). Attach the Upright Extension (12) to the ButterflyUpright (3) with two M10 x 95m
87. Press a 50mm x 75mm Inner Cap (58) into the topof the Squat Upright (4). Press two 25mm RoundOuter Cap (121) onto the Upright. Slide the SquatUpri
99. Attach a Roller (39) between the indicated set ofholes in the Squat Slider (38) with an M8 x 85mmBolt (94) and an M8 Nylon Locknut (34). Do notove
Comments to this Manuals