USER’S MANUALModel No. 831.159530Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe
8586Axle1015. Locate and open the parts bag labeled “ARMASSEMBLY.”Press a 2” Square Inner Cap (59) into each endof the Leg Lever (8).Lubricate the 3/8
1818. Press two 1 3/4” Square Inner Caps (60) into thetop of the Press Frame (14). Lubricate the 3/8” x 9” Bolt (92). Attach the PressFrame (14) to th
211224. Wrap the Press Cable (80) around a 3 1/2” Pulley(37). Attach the Pulley to the indicated side of thePress Frame (14) with a 3/8” x 3 1/2” Bolt
1327. Wrap the Press Cable (80) around a 3 1/2” Pulley(37). Attach the Pulley and a Cable Trap (44) tothe Press Upright (6) with a 3/8” x 3 3/4” Bolt(
1430. Wrap the Press Cable (80) around a “V”-Pulley(38). Attach the Pulley and a Long Cable Trap(50) to the indicated hole in the Press SeatFrame (12)
1534. Wrap the Press Cable (80) around a 3 1/2” Pulley(37). Attach the Pulley to the bracket on the TopFrame (5) with a 3/8” x 2” Bolt (79) and a 3/8”
1637. Wrap the Butterfly Cable (81) around a “V”-Pulley(38). Attach the Pulley and a Long Cable Trap(50) to the indicated side of the bracket on theBu
17413774494983RodBallLarge tabsmust be onthis side4757541. Identify the Ab Cable (83); it is approximately220.25” long and it has a ball on one end an
1845. Wrap the Ab Cable (83) around a 3 1/2” Pulley(37). Attach the Pulley to the bracket on theButterfly Top Frame (19) with a 3/8” x 2” Bolt (79)and
49501949. Wrap the Leg Press Cable (82) around a 3 1/2”Pulley (37). Attach the Pulley and a Cable Trap(44) to the Butterfly Upright (4) with a 3/8” x
2IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3BEF
2053. Locate and open the parts bag labeled “SEATASSEMBLY.”Press a 1 1/2” Square Inner Cap (100) into thebottom of a Seat Bracket (11). Press two 1” x
21561065790908451670218498100932057. Press a 1 3/4” Square Inner Cap (60) into theback of the Adjustment Tube (23). Attach the Adjustment Tube (23) to
592259. Attach the Curl Pad (36) to the Curl Post (35) withtwo 1/4” x 3/4” Bolts (90).35909036 60. Make sure that all parts have been properly tighten
ADJUSTING THE SEATTo adjust the height of the Seat (25) on the PressSeat Frame (12), loosen the Adjustment Knob (51) byturning it counterclockwise, an
24363559945474768482731WeightTube2852ATTACHING THE CURL PADTo use the Curl Pad (36), remove the 2” Square InnerCap (59) and insert the Curl Post (35)
25Weight High Arm Leg Butterfly Leg Lever Low Arm(lbs.) Pulley Press Press Arm (lbs.) Pulley(lbs.) (lbs.) (lbs.) (lbs.)* (lbs.)20 30 23 44 9 26 2240 6
26The cable diagrams below show the proper routing of the Butterfly Cable (81), the Ab Cable (83), the Leg LeverCable (82) and the Press Cable (80). T
27Slack can be removed form the Press Cable (80) bymoving the indicated “V”-Pulley (38) to one of the fourfree holes in the Press Seat Frame (12). Rem
Part No. 177796 R1001A Printed in Canada © 2001 Sears, Roebuck and Co.SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179Model No. 831.159530QUESTIONS?I
Note: Assembly is divided into four stages: 1) frame assembly; 2) armassembly; 3) cable assembly; and 4) seat assembly. The hardware foreach assembly
1. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibility of the owner to en
1” Retainer (85)1" CoverCap (86)1 3/4" Square Inner Cap (60)1" Inner Cap (32)1" x 2” Inner Cap (70)1 1/2" Round Inner Cap (67
3/8" Nylon Locknut (74)3/8" Nylon Jamnut (88)5/16" Nylon Jamnut (105)1/2" Nylon Locknut (95)1/4" x 1 3/4" Screw (98)5/16
3/8" x 3 1/2" Bolt (65)3/8" Washer (75)3/8" x 3 3/4" Bolt (62)3/8" x 9" Bolt (92)5/16" Washer (66)5/16" x
81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL
Key No. Qty. Description Key No. Qty. Description 1 1 Butterfly Base2 1 Center Base3 1 Press Base4 1 Butterfly Upright5 1 Top Frame6 1 Press Upright7
454847246446236066632274374444376196699589897474642292974323232323130303130302727272730303178787878282829298083333364747474205337915510737447434557965
4ASSEMBLED DIMENSIONS: Height: 77 in.Width: 103 in. Depth: 55 in. Low PulleyStationFoot PlateLeg LeverPress ArmsDecal 1Decal 1Decal 2BackrestCurl PadB
5Make sure you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mallet• You will
1. Before beginning, make sure that you haveread and understood the information on page 5.Locate and open the parts bags labeled“FRAME ASSEMBLY 1 and
4. Press a 1 1/2” Square Inner Cap (100) into theindicated part of the Press Upright (6).Orient the Press Upright (6) as shown. Attach thePress Uprigh
8. Attach the Top Frame (5) to the Butterfly Upright(4) with two 3/8” x 2 3/4” Bolts (58), a ShortSupport Plate (26), and two 3/8” Nylon Locknuts(74).
9121314555566669Adjustment knobmust be on this side6410546412597172364646655610 66666411. Press a 2” Square Inner Cap (59) into the PressTop Frame (13
Comments to this Manuals