Weider 831.159720 User Manual

®USER’S MANUALModel No. 831.159720Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONR

14. Locate and open the parts bag labeled “CABLEASSEMBLY AND PULLEYS.” For Cable identificationand routing during steps 14 to 32, refer to the CableDi

1115. Wrap the Short Cable over a “V” Pulley (21) asshown. Attach the “V” Pulley and a Long Cable Trap(14) to one side of the welded bracket on the Bu

1220. Attach the threaded shaft on the Medium Cable (72)to the Small “U”-Bracket (43) with a 1/4” Flat Washer(11) and a 1/4” Nylon Locknut (16). Note:

1324. Wrap the Long Cable (73) around a 3 1/2” Pulley (5).Attach the Pulley and a Cable Trap (39) to the indicat-ed bracket on the Butterfly Base (61)

1426. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)in the direction shown. Attach the Pulley and a CableTrap (39) to the indicated bracket on th

1529. Wrap the Long Cable (73) around a “V”-Pulley (21)in the direction shown. Attach the “V”-Pulley and aLarge Cable Trap (14) to the small tube on t

16Seat Assembly34. Press four 3/4” Round Inner Caps (40) into the endsof the Pad Tubes (48) and the indicated tubes on theLeg Lever (49) and the Press

17Miscellaneous Assembly36. Insert a 1/4” x 1 1/2” Carriage Bolt (82) through thecenter hole in a Seat Plate (42). Attach the Seat Plateto a Seat (51)

1839. Apply the WEIDER PRO 9930 decal in the locationshown. 40. Make sure that all parts have been properly tightened. The use of the remaining parts

19Cable DiagramsThe Cable Diagrams below and on the next page show the proper routing of the Short Cable (71), the MediumCable (72), and the Long Cabl

2Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20Long Cable (73)12345678913111210

21Using the Curl PadTo use the Curl Pad (69), insert the Curl Post (70) into theSeat Brace (75) and secure the Curl Post at the desiredheight with the

22Slack can be removed from the Long Cable (73) by mov-ing the 3 1/2” Pulley (5) on the Long Cable in the direc-tion shown. It is attached to the smal

23High Arm Butterfly Curl/ Leg RaiseWeight Pulley Press (lbs.) Low Pulley (lbs.)Plates (lbs.) (lbs.) (lbs.)Top 11 20 15 16 171 25 39 31 32 372 40 59 4

1" Round Inner Cap (41)1" Round Cap (26)3/4" Round Inner Cap (40)1 1/2" Square Inner Cap (79)1" Inner Cap (80)1 3/4" Squ

1/4" Flat Washer (11)5/16" Flat Washer (19)1" Retainer (25)3/8" Flat Washer (17)5/16" x 1 3/4" Bolt (9)3/8" Nylon L

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Part List—Model No. 831.159720

651370372526663765671818712526371871681527186951824213452228811161920742238734139535161395744395352241739535624552236262114383841462064238395720194663

Part No. 158932 R1299A Printed in Canada © 1999 Sears, Roebuck and Co.Model No. 831.159720QUESTIONS?If you find that:• you need help assembling orope

3Important PrecautionsWARNING: To reduce the risk of serious injury, read the following important precau-tions before using the home gym.1. It is the

4ASSEMBLED DIMENSIONS: Height: 78 in.Width: 65 in. Depth: 34 in. Low PulleyStationFoot PlatePress ArmBackrestCurl PadAdjustmentKnobButterflyArmsWeight

5Note: This introduction will save you more timethan it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h

61. Before beginning, make sure that you have readand understood the information on page 5.Locate and open the parts bag labeled “FRAMEASSEMBLY.”Press

73. Place two Weight Bumpers (84) over the indicatedholes in the Butterfly Base (61). Slide the WeightGuides (58) into the indicated holes.Attach the

87. Turn the Seat Brace (75) so the nut is on the side asshown. Attach the Seat Brace (75) to the ButterflyBase (61) with the 5/16” x 2 1/2” Carriage

911. Press a 1 1/2” Inner Cap (79) into the Press SeatFrame (52). Slide the bracket on the Press Seat Frame (52) ontothe indicated 5/16” x 2 1/2” Carr