USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or if there aremiss
1017. Route the Medium Cable (58) around the 3 1/2”Pulley (15) attached to the bracket on the TopFrame (55). Tighten the 3/8” x 2” Bolt (12) andthe 3/
1121. Attach the Medium Cable (58) to a Small “U”-Bracket (71) with a 1/4” Nylon Locknut (2)and a 1/4” Flat Washer (10). Do not tightenthe 1/4” Nylon
1224. Wrap the Long Cable (72) around a 3 1/2”Pulley (15). Attach the Pulley and two PulleyCovers (96) to the Squat Arm (84) with the3/8” x 2 1/4” Bol
1326. Attach the Backrest (41) to the Front Upright(42) with two 1/4” x 2 1/2” Screws (43) andtwo 1/4” Flat Washers (10).27. Press a 1 1/2” Inner Cap
1430. Press two 3/4” Round Inner Caps (34) intoeach 13 1/2” Pad Tube (28). Insert the 13 1/2” Pad Tube (28) into the SeatFrame (36). Slide a 6” Pad (3
15HOW TO USE THE HOME GYM SYSTEMThe instructions below describe how each part of the home gym system can be adjusted. IMPORTANT: Whenattaching the lat
16ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the SeatFrame (36) onto the indicated pins on the FrontUpright (42). Atta
17WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each station. “Top” refers to the 6,5 lbs. top weight. Theother numbers
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym
19CABLE DIAGRAMThe cable diagram below shows the proper routing of the Long Cable (72), the Medium Cable (58), and theShort Cable (23). Use the diagra
2IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautions before usingthe home gym system.WARNING:
ORDERING REPLACEMENT PARTSIf you encounter any difficulties or problems with this product, contact the ICON Fitness Lifestyle Ltd. office, orwrite: IC
WESY87300 R0600APlease note: The assembly is divided into five stages: 1) frame assembly, 2) press and butterflyarm assembly, 3) cable and pulley asse
5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)3/8" Nylon Jam Nut (92)5/16" x 2 1/
1" Retainer (69)5/16" x 6" Bolt (60)3/8" x 3 1/2" Bolt (16)1/4" x 3/4" Screw (18)5/16" x 5" Bolt (68)3/8
1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1/2" x 3/4" Spacer (61)5/16" x 2" Eyebolt (3
REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL!81
PART LIST—Model No. WESY87300 R0600ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
683202115661227837880757510817732837879310437411113511127195121525642612661563652427172367157621565483835253392193921594843882249828387852288382838760
3BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 74 in.Width: 60 in. Length: 54 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButte
4ASSEMBLY1745633811512714315127HighSide51. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Press
42352. Insert two 5/16” x 2 1/2” Carriage Bolts (1) upthrough the Base (4).Slide the Front Upright (42) onto the 5/16” x2 1/2” Carriage Bolts (1) in t
5665. Press a Weight Tube Bumper (64) into theend of a Weight Tube (63). Insert the WeightTube into the front stack of Weights (25). Besure that the p
7. Attach the upper ends of the Long WeightGuides (62) to the Top Frame (55) with a5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers(61), and a 5/16’ Nylo
811. Lubricate both axles on the Top Frame (55). Slide the Right Arm (48) onto the right axle.Be careful not to confuse the Right Armwith the Left Arm
9During steps 13 to 25, refer to the CABLE DIA-GRAM on page 19 of this manual. Identify thethree cables by their lengths, and note the posi-tions of t
Comments to this Manuals