USER'S MANUAL®Model No. WEEVSY52000Serial No. Write the serial number in the spaceabove for future reference.CAUTIONRead all precautions and inst
1948. Wrap the Low Cable (86) around a 3 1/2”Pulley (82). Attach the Pulley, a set of PulleyCovers (94), and a 3/8” Washer (38) to theAb Upright (1)
1118. Press a 1 3/4” Square Inner Cap (48) into thelower end of the Left Butterfly Arm (6). Wetthe lower end of the Left Butterfly Arm withsoapy water
1740. Note: The 3 1/2” Pulley (82) used in thisstep was attached in step 38. It is shownremoved for easier part identification.Route the Press Cable (
1325. Identify the Rear Cable (87)—this is theshortest Cable. Slide one end of the RearCable onto the 5/16” x 3” Bolt (92). Threadanother 5/16” Nylon
1532. Route the Press Cable (88) around a 3 1/2”Pulley (82). Attache the Pulley and a set ofPulley Covers (94) to the lowest set of holesin the Pulley
Note: Assembly is divided into four stages: 1) frame assembly, 2) armassembly, 3) cable assembly, and 4) seat assembly. The hardware foreach stage is
3/8" Nylon Jam Nut(43)5/16" x 2" Carriage Bolt (79)Cable Clip (33)5/16" x 1 3/4" Bolt (68)3/8" x 2" Bolt (50)5/16&q
81PART LIST—Model No. WEEVSY52000 R0101ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty.
123456778910111213141516171819172121222223232424252526262828292929293031323233343536212185858786314141868788888989566682384320555566503840205642828043
345712131419212223232424252526263232333435362121858731888989568280434250406940696767406837444037684467404067425520552049588343402055207682434398403764
272TABLE OF CONTENTSIMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3WARNING:To reduce the risk of serious injury, read the following important precautionsbefore using the training system.IMPORTANT PRECAUTIONS1. It is
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. Thetraining
5ASSEMBLY24WEIGHT PRESS BUTTERFLY LEG HIGH LOW LEG ABARM ARM LEVER PULLEY PULLEY PRESS PULLEYPLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)T
1.Locate and open the parts bags labeled“FRAME ASSEMBLY BAG ONE” and“FRAME ASSEMBLY BAG TWO.”Press two 2” Square Outer Caps (58) onto theWeight Base (
4. Slide the Front Seat Frame (8) onto the indi-cated 5/16” x 2 1/2” Carriage Bolts (49) in thePress Base (13). Hand tighten two 5/16”Nylon Locknuts (
565758SEAT ASSEMBLYMISC.8. Lubricate the insides of the holes in the TopWeights (24) as shown. Slide a Top Weightonto each set of Weight Guides (23).9
11. Attach the Leg Press Plate (11) to theAdjustment Tube (10) with a 5/16” x 2 1/4”Bolt (62), two 5/16” Washers (20), and a 5/16”Nylon Locknut (40).
Comments to this Manuals