CAUTIONRead all precautions and instruc-tions in this manual beforeusing this equipment. Save thismanual for future reference.Model No. WEEVSY2996.1Se
104. Attach the Frame (9) to the Upright (2) with twoM8 x 80mm Bolts (100), two M8 Washers (103),and two M8 Nylon Locknuts (78). Do not tightenthe Nyl
119. Attach a Shroud Cover (23) to the Left and RightShrouds (21, 22) with two M6 x 28mm Bolts (94),four M6 Washers (114), and two M6 NylonLocknuts (1
1210. Attach the Butterfly Frame Brace (6) to theUpright (2) with two M8 x 80mm Bolts (100), twoM8 Washers (103), and two M8 Nylon Locknuts(78). Do no
1313. Apply grease to the locations shown and attachthe Left Butterfly Bracket (28) to the ButterflyFrame (5) with an M10 x 80mm Bolt (84) and anM10 N
1416. Orient a Press Arm Handle (17) with the 90° bendat the top as shown in the inset drawing. Attach aPress Arm Handle (17) to the Right Press Arm(1
1519.See the CABLE DIAGRAM on page 28 to identifythe cables as you assemble them.Identify the Butterfly Cable (50).Grease anM8 x 22mm Shoulder Bolt (9
1622. Wrap the Butterfly Cable (50) over a “V”-pulley(47). Attach the “V”-pulley, a Long Cable Trap(57), an M10 Washer (80), and two Guards (54)to the
1725. Route the Lat Cable (49) over a Thin Pulley (24)and down through the Top Frame (4). Hold theThin Pulley inside the Top Frame. Insert an M10 x80m
1828. Wrap the Lat Cable (49) over a 90mm Pulley (48)and route the Cable down through the Top Frame(4). Attach the Pulley to the Top Frame with anM10
1931. Attach a 90mm Pulley (48) inside the Front Leg(10) with an M10 x 65mm Bolt (85), two M10Washers (80), two 13mm Steel Spacers (109),and an M10 Ny
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2IM
2034. Wrap the Leg Lever Cable (51) under a 90mmPulley (48). Attach the Pulley to the Base (1) withan M10 x 45mm Bolt (86), two Half Guards (55),and a
2137. Wrap the Leg Lever Cable (51) under a 90mmPulley (48). Attach the Pulley to the Right PressArm (16) with an M10 x 50mm Bolt (97), two HalfGuards
2240. Attach the Leg Lever Cable (51) to the Upright (2)with the M10 x 120mm Bolt (115), an M10Washer (80), a 7mm Spacer (111), and an M10Nylon Locknu
2343. Attach the Seat (32) to the Seat Frame (8) withtwo M6 x 16mm Screws (88), an M6 x 32mmScrew (89), and an M6 Washer (114).Insert the Seat Frame (
2446. Attach the Curl Pad (33) to the Curl Post (11) withtwo M6 x 16mm Screws (88).47. Make sure that all parts have been properly tightened. The use
25This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor-rect form for each exercise. Make sur
26USING THE CURL PADTo use the Curl Pad (33), remove the indicated 50mmRound Inner Cap (39) and insert the Curl Post (11)into the Front Leg (10). Tigh
27WEIGHT RESISTANCE CHARTThe chart below shows the approximate weight resistance at each exercise station. Note: Weight resistanceshown for the butter
28CABLE DIAGRAMThe cable diagram shows the proper routing of the cables (49, 50, 51). Use the diagram to make sure that thecable and the cable traps h
29Make sure all parts are properly tightened each time you use the weight system. Replace any worn partsimmediately. The weight system can be cleaned
1. Read all instructions in this manual and allwarnings on the weight system before usingthe weight system. Use the weight systemonly as described in
30EXERCISE GUIDELINESTHE FOUR BASIC TYPES OF WORKOUTSMuscle BuildingTo increase the size and strength of your muscles,push them close to their maximum
31Rest for a short period of time after each set. Theideal resting periods follow:•Rest for three minutes after each set for a musclebuilding workout.
32MONDAYDate://EXERCISE WEIGHT SETS REPSEXERCISE WEIGHT SETS REPSEXERCISE WEIGHT SETS REPSAEROBIC EXERCISEAEROBIC EXERCISETUESDAYDate:/ /WEDNESDAYDate
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back coverof this manual for information abou
315161717182122232323838404048484848555555555555555556565656559606010871727377777710677780808080808080808019393778197949410210294941029797777785801101
124567891011121313142527283031323334363636363737373738393938414141414243444646454547474748244848484848484848449505151525853545454555555555555555555555
Part No. 250520 R0107A Printed in China © 2007 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, contact the ICON Health & Fitnes
4BackrestCurl PadShroudWeightBackrestAdjustment KnobSeat Adjustment KnobAnkle StrapHandleCurl Adjustment KnobButterfly ArmSeatRight SideLeft SideNote:
89.5mm Spacer (59)56.5mm Spacer (69)21mm Steel Spacer (108)19mm Spacer (67)13mm Steel Spacer (109)11mm Spacer (99)M10 Nylon Locknut(77)M8 Washer (103)
M6 x 32mm Screw (89)M6 x 28mmBolt (94)M6 x 60mm Button Screw (91)M8 x 75mm Carriage Bolt (83)M8 x 80mm Bolt (100)M8 x 65mm Bolt (101)M10 x 120mm Bolt
7Backrest Adjustment Knob (53)Curl Adjustment Knobf (58)Seat Adjustment Knob (52)PART IDENTIFICATION CHART—Model No. WEEVSY2996.1 R0107A
8Make sure you have the following tools:• Two adjustable wrenches•One standard screwdriver• One Phillips screwdriver• One rubber mallet• You will also
92. Insert the two Weight Guides (18) into theStabilizer (3). Make sure that the indicatedholes in the Weight Guides are nearer thefloor.Attach the St
Comments to this Manuals