USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or if there are mis
1012. Press a 1Ó Round Inner Cap (49) into one ofthe Press Arms (46). Press a 1 3/4Ó SquareInner Cap (44) into the Press Arm.Attach the Press Arm (46)
1115. See the inset drawing. Attach the MilitaryPress Arm (84) to the Pivot Arm (80) with two5/16Ó x 2 1/4Ó Bolts (33) and two 5/16Ó NylonLocknuts (3)
1218. Wrap the High Cable (58) around a ÒVÓ-Pulley(50). Attach the ÒVÓ-Pulley and a Long CableTrap (31) to the indicated bracket on the FrontUpright (
1322. See the inset drawing. Attach a 3 1/2Ó Pulley(15) and a Cable Trap (66) to the upper hole ina Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó Bolt(12) an
1425. Locate the Low Cable (23) and the baglabeled ÒLOW PULLEY.Ó Route the LowCable under the 3 1/2Ó Low Pulley (76).Attach the Pulley and the 5/8Ó x
1529. Attach the end of the Low Cable (23) to theLong ÒUÓ-Bracket (57) with a 1/4Ó NylonLocknut (2) and a 1/4Ó Flat Washer (10). You may need to lift
1632. Wrap the Military Press Cable (72) around a 31/2Ó Pulley (15). Attach the Pulley and aCable Trap (66) to the Pivot Arm (80) with the3/8Ó x 5Ó Bo
17CABLE ASSEMBLY35. Locate the Leg Press Cable (78). Attach theend of the Leg Press Cable to the Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon Locknut (2) a
1839. Attach the Front Backrest (41) to the FrontUpright (42) with two 1/4Ó x 2 1/2Ó Screws(43) and two 1/4Ó Flat Washers (10).40. Press a 1 1/2Ó Squa
19SEAT ASSEMBLY43. Press two 3/4Ó Round Inner Caps (34) intoeach Pad Tube (28). Insert a Pad Tube (28) into the Front SeatFrame (36). Slide a Foam Pad
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20SEAT ASSEMBLY44. Remove the adhesive backing from the CLUB WEIDER¨16.4ST decal and apply it to the Front Upright (42)under the ÒWEIDERÓ nameplate as
21HOW TO USE THE HOME GYM SYSTEMThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter acco
22ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the FrontSeat Frame (36) onto the indicated pins on the FrontUpright (42)
23WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. ÒTopÓ refers to the 6.5 lb. top weight.The other n
24TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy
25CABLE DIAGRAMSThe cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), theMilitary Press Cable (72), an
26Military Press Cable (72)Leg Press Cable (78)Rear Weight StackÑ12346578Ball End324ÑRear Seat Frame1ÑLong ÒUÓ-BracketMilitary Press Cable (72) and Le
27NOTES
5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)1/4" x 2 1/2" Screw (43)3/8" N
1" Retainer (69)3/8" x 3 1/2" Bolt (16)1/4" x 3/4" Screw (18)5/16" x 5" Bolt (68)3/8" x 3 3/4" Bolt (88)3
3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the home gym system.1. It is the responsibility o
1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1/2" x 3/4" Spacer (61)5/16" x 2" Eyebolt (3
PART LISTÑModel No. WESY39200 R0900ANote: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
602721155512118151244881558214421361622435871265636425261921933496224646163915215923211727141043414221350318670696970214744454445485031861340383718323
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 89 in. Length: 64 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg LeverButter
5ASSEMBLY1811512714315151. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Locate and open the p
62. Slide the Rear Upright (74) and the Leg PressUpright (56) onto the indicated 5/16Ó x 2 1/2ÓCarriage Bolts (1) in the Stabilizer (5). Thehigh side
74. Press a 2Ó Square Inner Cap (27) into the endof the Top Frame (55). Press a 1 3/4Ó SquareInner Cap (44) into each end of the crossbaron the Top Fr
87. Press a Weight Tube Bumper (64) into theend of a Weight Tube (63). Insert the WeightTube into the front stack of Weights (25). Besure that the pin
99. Attach the upper ends of the Short WeightGuides (73) to the Top Frame (55) with a 5/16Óx 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), anda 5/16Ó Ny
Comments to this Manuals