Weider WESY1972 User Manual

USER’S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are miss-i

1015. Route the Long Cable (23) around the “V”-Pulley (6) on the Right Arm (48). Be surethat the Cable is in the groove of the “V”-Pulley and that the

11CABLE ASSEMBLY19. Loosen the M10 Nylon Locknut (21) on thelower 3 1/2” Pulley (15) on the PressFrame (17).Locate the Short Cable (58). Route theShor

1221. Route the Short Cable (58) around the 3 1/2”Pulley (15) attached to the upper hole in thePress Frame (17). Be sure that the CableTrap (66) is tu

23. Attach the end of the Short Cable (58) to theLong “U”-Bracket (57) with an M8 Nylon Lock-nut (3) and a 5/16” Flat Washer (8). Do notcompletely tig

1425. Attach the Backrest (41) to the Front Upright(42) with two M6 x 65mm Screws (43) andtwo 1/4” Flat Washers (10).26. Press a 1 1/2” Square Inner C

1528. Rest the Seat Frame (36) on the indicated pinin the Front Upright (42). Attach the SeatFrame to the Front Upright with a M8 x 67mmCarriage Bolt

1630. Remove the decals from the decal sheet (not shown) and apply them to the weight system in the locationsshown below.HIGH PULLEYBUTTERFLY8515BENCH

17ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

18ATTACHING AND REMOVING THE SEATSet the bracket on the Seat Frame (36) onto the indi-cated pins on the Front Upright (42). Attach the SeatFrame to th

19TROUBLESHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately.

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw

21NOTES

22Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY19720 R0902AKey No. Qty. De

231111885527781544157723272144213616035615123575821355114192651256463769213341276515714110433216507427506216970697047484445444513403837183228303410224

LIMITED WARRANTYORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondayt

Note: The assembly is divided into four stages: 1) frame assembly, 2) armassembly, 3) cable assembly, and 4) seat assembly. The hardware foreach stage

1/4" Flat Washer (10)–45/16" Flat Washer (8)–73/8" Flat Washer (9)–4M8 x 45mm Bolt (72)–1M10 Nylon Locknut (21)–12M6 x 16mm Screw (18)–

1" Round Inner Cap (49)–61" Round Cover Cap (70)–23/4" Round Inner Cap (34)–41/2" x 3/4" Spacer (61)—2M8 x 50mm Eyebolt (35)—

3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.1. Read al

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76 in.Width: 38 in. Length: 53 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButte

5ASSEMBLY156High Side ofBracket355151141274Before beginning assembly, carefully read thefollowing information and instructions:• Place all parts of th

6FRAME ASSEMBLY2. Slide the Front Upright (42) onto the M8 x63mm Carriage Bolts (1) in the Base (4).Hand tighten an M8 Nylon Locknut (3) ontoeach Carr

7FRAME ASSEMBLYARM ASSEMBLY5. Press the Weight Tube Bumper (64) into theend of the Weight Tube (63). Insert theWeight Tube into the stack of Weights (

8ARM ASSEMBLY8. Press a 1 3/4” Square Inner Cap (44) into thetop of a Press Arm (46). Press a 1” RoundInner Cap (49) into each end of the handle onthe

9CABLE ASSEMBLY11. During steps 11 through 25, refer to theCABLE DIAGRAM on page 20 of this manualto verify proper cable routing. Before begin-ning th