Weider WEEVSY3953 User Manual

USER'S MANUALModel No. WEEVSY39530Serial No. Write the serial number in thespace above for future reference.CAUTIONRead all precautions and instr

1014. Open the parts bag labelled “ARM ASSEMBLY.”Press three 40mm x 50mm Inner Caps (21) into theLeg Lever (10).Lubricate an M10 x 65mm Bolt (18) with

18.Locate and open the parts bags labelled“CABLE ASSEMBLY”, “PULLEY COVERS”, and“PULLEYS.”Lubricate the M10 x 165mm Bolt (30) with grease.Attach the S

1220. Remove the preattached 90mm Pulleys (78)from the Small Pulley Plates (31).Wrap the Swivel High Cable (74) under a 90mmPulley (78). Attach the Pu

1324. Remove the preattached 90mm Pulleys (78)from the Offset Double “U”-bracket (61).Wrap the Swivel Cable (17) around a 90mm Pulley(78). Attach the

1429. Wrap the Lat Cable (88) around a 90mm Pulley(78). Attach the Pulley and a Cable Trap (102) tothe Top Frame (6) with an M10 x 50mm Bolt (100)and

153536383734. Remove the preattached 90mm Pulleys (78)from the Double “U”-bracket (62).Wrap the Butterfly Cable (69) under a 90mm Pulley(78). Attach t

1641. Remove the preattached 90mm Pulley (notshown) from the “U”-bracket (64).Attach the end of the Leg Lever Cable (75) to the“U”-bracket (64) with a

1745. Wrap the Swivel Low Cable (72) under a 90mmPulley (78). Attach the Pulley and a pair of PulleyCovers (68) to the indicated bracket on the LongBa

1849. Wrap the Swivel Low Cable (72) over a 90mmPulley (78). Attach the Pulley and a pair of PulleyCovers (68) between the lower set of holes in the“U

1953. Wrap the Squat Cable (73) under a 90mm Pulley(78). Attach the Pulley and a pair of Pulley Covers(68) to the second set of holes from the top in

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2057. Press two 20mm x 40mm Inner Caps (116) and a25mm x 40mm Inner Cap (117) into the SeatBracket (11). Attach the Seat (16) to the Seat Bracket (11)

216161. Turn the Squat Backrest (35) so that the four screwholes are closer to the bottom of the SquatBackrest than the top. Attach the Squat Backrest

22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

23ADJUSTING THE SQUAT ARM, SEAT, ORBUTTERFLY BACKRESTTo adjust the height of the Squat Arm (32), first loosenthe Adjustment Knob (115) on the Squat Br

HIGH PULLEY(lbs.)1425384861688096101112122LOW PULLEY(lbs.)1425364460708091104111122LEGLEVER(lbs.)2235536791111122148160184190BUTTERFLYARM(lbs.)1726364

25TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately. The weight sys

26CABLE DIAGRAMSThe cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-grams on this page and

27Leg LeverCable (75)Swivel LowCable (72)113245679234123458Swivel Cable (17)

ORDERING REPLACEMENT PARTSTo order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write: Unit 4Revie Road Industrial Estate

Note: Assembly is divided into four stages: 1) frame assembly, 2) armassembly, 3) cable assembly, and 4) seat assembly. The hardware foreach stage is

IMPORTANT PRECAUTIONS31. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibil

50mm x 75mm Inner Cap (58)40mm x 50mm Inner Cap (21)25mm Round Inner Cap (29)50mm x 70mm Inner Cap (95)38mm Square Inner Cap (67)50mm Square Inner Cap

Cable Clip (83)90mm Pulley (78)(Not shown to scale)"V"-pulley (55)(Not shown to scale)115mm Pulley (119)(Not shown to scale)M10 Nylon Locknu

M10 x 20mm Bolt (86)M10 x 60mm Bolt (59)M10 x 70mm Bolt (85)M10 x 95mm Bolt (92)M10 x 45mm Bolt (93)M10 x 85mm Bolt (96)M10 x 165mm Bolt (30)M10 x 50m

PART LIST—Model No. WEEVSY39530 R0803ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 50mm Washer

81REMOVE THIS PART LIST/EXPLODED DRAWINGFROM THE MANUAL.SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE

465732891011131516109109191920202121202123242526272728292928323333111111383939424243434745444544484849505011411452525555565757575854542160606465656710

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 81 in., 202.5 cmWidth: 102 in., 255 cm Length: 52 in., 130 cmSquat Knee RestAb StrapCurl BarHandleLow P

5ASSEMBLYMake sure that you have the following tools:• Two adjustable spanners• One standard screwdriver• One phillips screwdriver• One rubber mal

1.Locate and open the parts bags labelled“FRAME ASSEMBLY 1” and “FRAME ASSEMBLY2.”See the inset drawing. Attach the Base Cap (24)to the Short Base (2)

4. Press a 38mm Square Inner Cap (67) into theUpright Extension (12). Attach the Upright Extension (12) to the ButterflyUpright (3) with two M10 x 95m

87. Press a 50mm x 75mm Inner Cap (58) into the topof the Squat Upright (4). Press two 25mm RoundOuter Caps (121) onto the Upright. Slide the SquatUpr

99. Attach a Roller (39) between the indicated set ofholes in the Squat Slider (38) with an M8 x 85mmBolt (94) and an M8 Nylon Locknut (34). Do notove