USER'S MANUALQUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or if there aremiss
1015. Route the Long Cable (23) around the “V”-Pulley (6) on the Right Arm (48). Be surethat the Cable is in the groove of the “V”-Pulley and that the
11CABLE ASSEMBLY19. Note: This assembly step shows how tocomplete the assembly of several pre-attached parts.The 5/8” x 9/16” Spacer (73) has been pre
1221. Route the Short Cable (58) around the 3 1/2”Pulley (15) attached to the lower hole in theFront Upright (42). See the inset drawing.Be sure that
24. Attach the end of the Short Cable (58) to theLong “U”-Bracket (57) with a 1/4” Nylon Lock-nut (2) and a 1/4” Flat Washer (10). Do notcompletely ti
1426. Attach the Backrest (41) to the Front Upright(42) with two 1/4” x 2 1/2” Screws (43) andtwo 1/4” Flat Washers (10).27. Press a 1 1/2” Square Inn
1529. Rest the Seat Frame (36) on the indicated pinin the Front Upright (42). Attach the SeatFrame to the Front Upright with a 5/16” x23/4” Carriage B
1631. Remove the decals from the decal sheet (not shown) and apply them to the weight system in the locationsshown below.HIGH PULLEYBUTTERFLY8510BENCH
17ADJUSTMENTThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseposter accompanying this manual t
18ATTACHING AND REMOVING THE SEATSet the bracket on the Seat Frame (36) onto the indi-cated pins on the Front Upright (42). Attach the SeatFrame to th
19TROUBLESHOOTING AND MAINTENANCEInspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. Theweight syst
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use thediagram to be sure that the tw
21Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.PART LIST—Model No. WESY8510C4 R1102AKey No. Qty. De
222311118855271215441571232721442136160356151225758213551141926512564637692133412765157141104332165074275062169706970474844454445134038371832283034102
23ICON of Canada Inc.900 de lʼIndustrieSt-Jérôme, QuébecCanada, J7Y 4B8PLACESTAMPHEREORDERING REPLACEMENT PARTSTo order replacement parts, call our Cu
5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)3/8" Flat Washer (9)1/4" x 2 1/2" Screw (43)5/16"
1" Retainer (69)3/8" x 2" Bolt (12)3/8" x 3 1/2" Bolt (16)3/8" x 2 1/2" Bolt (7)3/8" x 3 3/4" Bolt (71)3/
1" Round Inner Cap (49)1" Round Cover Cap (70)3/4" Round Inner Cap (34)1/2" x 3/4" Spacer (61)1" Round Inner Cap (78)1 1
Part No. 185279 R1102A Printed in Canada © 2002 ICON Health & Fitness, Inc.LIMITED WARRANTYICON OF/DU CANADA INC., (ICON), warrants this product t
3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.IMPORTANT PRECAUTIONS1. Read al
4BEFORE YOU BEGINASSEMBLEDDIMENSIONS:Height: 30 cm (76 in.)Width: 15 cm (38 in.)Length: 21 cm (53 in.)Foot PlateLow Pulley StationHigh Pulley StationL
5ASSEMBLY156High Side ofBracket355151141274Before beginning assembly, carefully read thefollowing information and instructions:• Place all parts of th
6FRAME ASSEMBLY2. Slide the Front Upright (42) onto the 5/16” x2 1/2” Carriage Bolts (1) in the Base (4).Hand tighten a 5/16” Nylon Locknut (3) ontoea
7FRAME ASSEMBLYARM ASSEMBLY5. Press the Weight Tube Bumper (64) into theend of the Weight Tube (63). Insert theWeight Tube into the stack of Weights (
8ARM ASSEMBLY8. Press a 1 3/4” Square Inner Cap (44) into thetop of a Press Arm (46). Press a 1” RoundInner Cap (49) into each end of the handle onthe
9CABLE ASSEMBLY11. During steps 11 through 25, refer to theCABLE DIAGRAM on page 20 of this manualto verify proper cable routing. Before begin-ning th
Comments to this Manuals