Weider WEEVSY6200 User Manual

QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If youhave questions, or if there aremissing or damaged par

1012. Press a 1” Round Inner Cap (49) into one ofthe Press Arms (46). Press a 1 3/4” SquareInner Cap (44) into the Press Arm.Attach the Press Arm (46)

1115. See the inset drawing. Attach the MilitaryPress Arm (84) to the Pivot Arm (101) withtwo 5/16” x 2 1/4” Bolts (33) and two 5/16”Nylon Locknuts (3

1217. Attach the Left Pull-up Arm (75) and the RightPull-up Arm (77) to the Assist Upright (74)with two 5/16” x 2 3/4” Bolts (11) and two5/16” Nylon L

1320. Wrap the High Cable (58) around a “V”-Pulley(50). Attach the “V”-Pulley and a Long CableTrap (31) to the indicated bracket on the FrontUpright (

1424. See the inset drawing. Wrap the High Cable(58) around a 3 1/2” Pulley (15). Attach thePulley and a set of Pulley Covers (114) to theupper hole i

1527. Locate the Low Cable (23). Route the LowCable under the 3 1/2” Low Pulley (102). Besure that the end of the Cable with the ballis on the indicat

1631. Attach the end of the Low Cable (23) to theLong “U”-Bracket (57) with a 1/4” NylonLocknut (2) and a 1/4” Flat Washer (10). Donot completely tigh

1734. Wrap the Military Press Cable (72) around a“V”-Pulley (50). Attach the “V”-Pulley to theTop Frame (55) with a 3/8” x 2 1/2” Bolt (86)and a 3/8”

1836. Slide a 5/16” Flat Washer (8) onto a 5/16” x 23/4” Bolt (11). Insert the Bolt through the indi-cated hole in the Pivot Arm (101). The Boltmust

1938. Locate the Leg Press Cable (99). Attach theend of the Leg Press Cable to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) anda 1/4” Flat

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2040. Locate and open the parts bag labelled“SEAT ASSEMBLY.”Insert a 1/4” x 2 1/2” Carriage Bolt (92)through the centre hole in a Seat Plate (37).Atta

2143. Attach the Front Backrest (41) to the FrontUpright (42) with two 1/4” x 2 1/2” Screws (43)and two 1/4” Flat Washers (10). The Backrestmust be or

2247. Press two 3/4” Round Inner Caps (34) intoeach Pad Tube (28). Insert a Pad Tube (28) into the Front SeatFrame (36). Slide a Foam Pad (30) onto ea

23HOW TO USE THE HOME GYM SYSTEMThe instructions below describe how each part of the home gym system can be adjusted. IMPORTANT: When attaching the la

24ATTACHING AND REMOVING THE SEATTo attach the Seat (13), set the bracket on the FrontSeat Frame (36) onto the indicated pins on the FrontUpright (42)

25WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6,5-pound topweight. The other

26TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy

27Military Press Cable (72)Leg Press Cable (99)1—RearWeight Stack234765324—Rear Seat Frame8—Pivot Arm1—Long “U”-BracketLow Cable (23)1—Low Pulley2345—

ORDERING REPLACEMENT PARTSIf you encounter any difficulties with this product, or if you need to order replacement parts, call the ICON Health& Fi

WEEVSY62000 R0301ANote: Assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable and pulleyassembly, and 4) seat and backres

3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the home gym system.IMPORTANT PRECAUTIONS1. It is

1" Round Inner Cap (49)1" Round Cover Cap (70)5/16" x 2" Eyebolt (35)Round Inner Cap (111)1 1/2" Square Inner Cap (32)2"

5/16" Nylon Locknut (3)1/4" Flat Washer (10)5/16" Flat Washer (8)1" Retainer (69)3/8" Flat Washer (9)3/8" Nylon Locknut

81REMOVE THIS PART LIST/EXPLODEDDRAWING CHART FROM THE MANUAL

PART LIST—Model No. WEEVSY62000 R0301ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 110 5/16” x 2 1

602721505586118151244881558214421361622435871265108642526199334962246461639152159232117271410434142213503186706969702147444544454850318613403837183234

4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 198 cmWidth: 218 cmLength: 168 cm Foot PlateHigh Pulley StationLat BarLeg LeverButterfly ArmsAssist Arm

518811512714315151. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Locate and open the parts ba

62. Slide the Assist Upright (74) and the LegPress Upright (56) onto the indicated 5/16” x2 1/2” Carriage Bolts (1) in the Stabiliser (5).The high sid

74. Press a 2” Square Inner Cap (27) into the endof the Top Frame (55). Press a 1 3/4” SquareInner Cap (44) into each end of the crossbaron the Top Fr

87. Press a Weight Tube Bumper (64) into theend of the Short Weight Tube (108). Insert theWeight Tube into the front stack of Weights(25). Be sure tha

99. Attach the upper ends of the Short WeightGuides (73) to the Top Frame (55) with a 5/16”x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), anda 5/16” Ny