Weider WEEVSY2026 User Manual

USER'S MANUALCAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manualfor future reference.Model

1012. Route the High Cable (50) over a 90mm Pulley(34) and down through the Top Frame (4).Attach the Pulley and a Cable Trap (36) to thebracket on the

1116. Locate the Press Cable (49). Slide the Cableonto the hook on the Left Arm (7).17.Apply grease to an M10 x 78mm Bolt (54).Attach the Pulley Arm (

1219. Apply grease to an M10 x 78mm Bolt (54).Attach a Pulley Arm (38) to the Upright (3) withthe Bolt and an M10 Nylon Locknut (68). Donot overtighte

1323. Attach the end of the Short Cable (47) to the“U”-bracket (43) with an M8 Washer (71) andan M8 Nylon Locknut (69). Note: Do not com-pletely tight

1427. Route the Low Cable (48) over a 90mm Pulley(34). Attach the Pulley, a Cable Trap (36), andtwo Finger Guards (35) to the lower set of holesin the

1531. Attach the Seat (19), oriented as shown, to theSeat Frame (8) with four M6 x 16mm Screws(40).32. Slide a Pad Tube (45) through the hole in theLe

1635. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained inADJUSTMENTS, on the next page. Before

17This section explains how to adjust the weight system. Refer to the accompanying exercise guide to see the cor-rect form for each exercise. Make sur

18WEIGHT RESISTANCE CHARTThe chart below shows the approximate weight resistance at each exercise station. Weight resistance shown forthe butterfly ar

19The cable diagrams below show the proper routing of the Short Cable (47), the Low Cable (48), the PressCable (49), and the High Cable (50). Use the

WARNING DECAL PLACEMENT2WEIDER is a registered trademark of ICON IP, Inc.WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . .

20TROUBLESHOOTING AND MAINTENANCETIGHTENING THE CABLESWoven cable, the type of cable used on the weightsystem, can stretch slightly when it is first u

1 1 Base21 Stabilizer3 1 Upright4 1 Top Frame5 1 Press Frame6 1 Right Arm7 1 Left Arm8 1 Seat Frame9 1 Leg Lever10 2 Weight Guide11 1 Small “U”-bracke

945248181921212122222245404082862122245672020747424242626252427272829294949647070687272616165737373736523244444353435353435685236364335343547526968713

323133329354235343435356868535321741417070575937101112131516506270687060716969318353435353438383925345254686866716369546868527367736746706968697071695

ORDERING REPLACEMENT PARTSTo order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write: ICON Health & Fitness, Ltd.Uni

31. Read all instructions in this manual and inthe accompanying literature and all warningson the weight system before using theweight system. Use the

4BEFORE YOU BEGINThank you for selecting the versatile WEIDER®PRO2000 weight system. The weight system offers a selec-tion of weight stations designed

M6 Washer (73)M8 Washer (71)M8 Nylon Locknut (69)M10 Washer (70)M10 Nylon Locknut (68)M6 Nylon Locknut (72)M4 Washer (77)M10 x 125mm Bolt (64)M10 x 15

6Before beginning assembly, carefully read thefollowing information and instructions:• Assembly requires two people.• Place all parts in a cleared are

72. Attach the Upright (3) to the Base (1) with the twoM8 x 63mm Carriage Bolts (58) and two M8Nylon Locknuts (69). Do not tighten the NylonLocknuts y

875777688638266. Attach the Seat Frame (8) to the Upright (3) withan M8 x 70mm Carriage Bolt (86) and an M8Knob (82).Attach the Bumper (75) to the Sea

99. Attach an Arm Pad (20) to the Left Arm (7) withtwo M6 x 58mm Screws (65) and two M6Washers (73).Repeat this step with the Right Arm (6).8. Apply g