USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
1015. Attach a Press Arm (7) to one side of the PressFrame (12) with two M8 x 63mm Bolts (39) andtwo M8 Nylon Locknuts (40).Attach the other Press Arm
1117. Wet the lower end of the Left Fly Arm (6) withsoapy water. Slide a Large Pad (22) onto the LeftFly Arm.Repeat this step with the Right Fly Arm (
1220. Wrap the Butterfly Cable (89) around a 90mmPulley (82) as shown. Attach the Pulley and aCable Trap (80) to the bracket on the Leg PressUpright (
1324. Identify the Rear Cable (87)—this is the short-est Cable. Remove the M8 x 69mm ShoulderBolt (43) from the Top Frame (2). Loosen the indi-cated M
1428. Identify the Press Cable (88)—this is thelongest Cable. Attach the end of the Press Cableto the Large “U”-bracket (84) with an M8 NylonLocknut (
1531. Route the Press Cable (88) over a 90mm Pulley(82). Attach the Pulley and a Cable Trap (80) tothe lower hole in the Pulley Plates (31) with anM10
1635. Route the Press Cable (88) over a 90mm Pulley(82). Attach the Pulley and a Cable Trap (80) tothe indicated hole in the Press Frame (12) withan M
1739. Note: The 90mm Pulley (82) used in this stepwas attached in step 38. It is shown removedfor easier part identification.Route the Press Cable (88
1843. Route the High Cable (85) under a 90mm Pulley(82). Attach the Pulley and a Cable Trap (80) tothe single hole end of the Pulley Plates (31) witha
1947. Wrap the Low Cable (86) around a 90mm Pulley(82). Attach the Pulley and a Cable Trap (80) tothe Ab Upright (1) with the M10 x 92mm Bolt (76)and
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50. Locate and open the parts bag labeled “SEATASSEMBLY.”Attach the Small Backrest (18) to the Ab Upright(1) with two M6 x 63mm Machine Screws (64)and
5455562157.Make sure that all parts have been properly tightened. The use of the remaining parts will be explained inADJUSTMENTS, beginning on the fol
22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t
23ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Ab Strap (35) to the Low Cable (86) at theab pulley station with a Cable Clip (33). ATTACHI
24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other n
To tighten the cables, first insert the weight pin into the mid-dle of the weight stack. Slack can be removed from thesecables several ways:• See draw
26CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the High Cable (85), the LowCable (86), the Rear Cable (8
27High Cable (85) Rear Cable (87)Weight Stack—5High Pulley—122331—Top Frame4—Weight Stack4
M6 Washer (37)M10 Nylon Locknut (42)M8 Nylon Locknut (40)M6 Nylon Locknut (44)M8 Washer (20)M10 x 48mm Bolt (50)M10 x 60mm Bolt (65)M10 x 57mm Bolt (9
M10 x 195mm Bolt (52)M10 x 82mm Bolt (66)M10 x 80mm Bolt (71)M10 x 120mm Bolt (74)M10 x 97mm Bolt (95)M10 x 92mm Bolt (76)M8 x 67mm Bolt (55)M8 x 152m
IMPORTANT PRECAUTIONS3WARNING: To reduce the risk of serious injury, read the following important precautionsbefore using the weight system.1. Read al
PART LIST—Model No. WESY26331 R0904AKey No. Qty. Description1 1 Ab Upright21 Top Frame3 1 Butterfly Frame4 1 Leg Press Upright5 1 Right Fly Arm6 1 Lef
123456778910111213141516171819172121222223232424252526262727282829292929303132323334353621218585878631414186878888898956768238422055557650385520564282
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-877-992-5999, Mondaythrough Friday, 6
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 64 in. Length: 70 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg LeverButter
5ASSEMBLYMake sure you have the following tools:• Two (2) adjustable wrenches• One (1) standard screwdriver• One (1) phillips screwdriver• One (1)
1.Locate and open the parts bags labeled“FRAME ASSEMBLY.”Insert six M8 x 63mm Carriage Bolts (49) upthrough the Press Base (13) and the Weight Base(14
4. Slide the Front Seat Frame (8) onto the indicatedM8 x 63mm Carriage Bolts (49) in the Press Base(13). Hand tighten two M8 Nylon Locknuts (40)onto t
8. Lubricate the insides of the indicated holes in theTop Weights (24) with the included grease. Slidea Top Weight onto each set of Weight Guides(23).
11. Locate and open the parts bag labeled “ARMASSEMBLY.”Attach the Leg Press Plate (11) to the AdjustmentTube (10) with an M8 x 60mm Bolt (62), two M8
Comments to this Manuals