USER’S MANUALModel No. 831.159531Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe
8586Axle1015. Locate and open the parts bag labeled “ARMASSEMBLY.”Press a 50mm Square Inner Cap (59) into eachend of the Leg Lever (8).Lubricate the M
1818. Press two 45mm Square Inner Caps (60) into thetop of the Press Frame (14). Press six M10 BrassBushings (77) into the Press Frame and thePress To
211224. Wrap the Press Cable (80) around a 90mmPulley (37). Attach the Pulley to the indicated sideof the Press Frame (14) with an M10 x 85mmBolt (88)
1327. Wrap the Press Cable (80) around a 90mmPulley (37). Attach the Pulley and a Cable Trap(44) to the Press Upright (6) with an M10 x 95mmBolt (62),
1430. Wrap the Press Cable (80) around a “V”-Pulley(38). Attach the Pulley and a Long Cable Trap(50) to the indicated hole in the Press SeatFrame (12)
1534. Wrap the Press Cable (80) around a 90mmPulley (37). Attach the Pulley to the bracket onthe Top Frame (5) with an M10 x 45mm Bolt (96)and an M10
1637. Wrap the Butterfly Cable (81) around a “V”-Pulley(38). Attach the Pulley and a Long Cable Trap(50) to the indicated side of the bracket on theBu
17413774494983RodBallLarge tabsmust be onthis side4959541. Identify the Ab Cable (83); it is approximately220.40” long and it has a ball on one end an
1845. Wrap the Ab Cable (83) around a 90mm Pulley(37). Attach the Pulley to the bracket on theButterfly Top Frame (19) with an M10 x 45mmBolt (96) and
49501949. Wrap the Leg Lever Cable (82) around a 90mmPulley (37). Attach the Pulley and a Cable Trap(44) to the Butterfly Upright (4) with an M10 x120
2IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3BEF
2053. Locate and open the parts bag labeled “SEATASSEMBLY.”Press a 25mm x 40mm Inner Cap (63) into thebottom of a Seat Bracket (11). Press two 25mm x5
215664579090665167021849863542057. Press a 45mm Square Inner Cap (60) into theback of the Adjustment Tube (23). Attach the Adjustment Tube (23) to the
592259. Attach the Curl Pad (36) to the Curl Post (35) withtwo M6 x 16mm Screws (90).35909036 60. Make sure that all parts have been properly tightene
ADJUSTING THE SEATTo adjust the height of the Seat (25) on the PressSeat Frame (12), loosen the Adjustment Knob (51) byturning it counterclockwise, an
2436355994547476848273131WeightTube2852ATTACHING THE CURL PADTo use the Curl Pad (36), remove the 50mm SquareInner Cap (59) and insert the Curl Post (
25Weight High Press Leg Butterfly Leg Lever Low Pulley Ab(lbs.) Pulley Arm Press Arm (lbs.) (lbs.) Pulley(lbs.) (lbs.) (lbs.) (lbs.) (lbs.)20 30 23 4
26The cable diagrams below show the proper routing of the Butterfly Cable (81), the Ab Cable (83), the Leg LeverCable (82) and the Press Cable (80). T
27Slack can be removed from the Press Cable (80) bymoving the indicated “V”-Pulley (38) to one of the fourfree holes in the Press Seat Frame (12). Rem
M6 x 16mm Screw (90)M6 x 65mm Screw (94)M8 x 40mm Carriage Bolt (54)M8 Nylon Locknut (64)M8 Washer (66)M10 Nylon Locknut (74)M6 Washer (84)M10 x 65mm
M10 x 120mm Bolt (61)M10 x 95mm Bolt (62)M10 x 90mm Bolt (55)M10 x 105mm Bolt (69)M10 x 85mm Bolt (88)M10 x 100mm Bolt (91)M10 x 81mm Bolt (93)M10 x 7
1. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibility of the owner to en
25mm Round Inner Cap (32)50mm Square Inner Cap (59)45mm Square Inner Cap (60)25mm x 40mm Inner Cap (63)38mm Round Inner Cap (67)25mm x 50mm Inner Cap
Key No. Qty. Description Key No. Qty. Description 1 1 Butterfly Base2 1 Center Base3 1 Press Base4 1 Butterfly Upright5 1 Top Frame6 1 Press Upright7
454847247446236095792274374444376188777489897474742292974323232323130303030272727273030317878787828282929808333337474747420533762583437447434589655377
Part No. 180383 R1201A Printed in China © 2001 Sears, Roebuck and Co.SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179Model No. 831.159531QUESTIONS?If
4ASSEMBLED DIMENSIONS: Height: 77 in.Width: 103 in. Depth: 57 in. Low PulleyStationFoot PlateLeg LeverPress ArmsDecal 1Decal 1Decal 2BackrestCurl PadB
5Make sure you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mallet• You will
1. Before beginning, make sure that you haveread and understood the information on page 5.Locate and open the parts bags labeled“FRAME ASSEMBLY 1 and
4. Press a 38mm Square Inner Cap (75) into theindicated tube on the Press Upright (6).Orient the Press Upright (6) as shown. Attach thePress Upright t
8. Attach the Top Frame (5) to the Butterfly Upright(4) with two M10 x 70mm Bolts (58), a ShortSupport Plate (26), and two M10 Nylon Locknuts(74). Do
9121314585895959Adjustment knobmust be on this side7410767412593747458610 959574411. Press a 50mm Square Inner Cap (59) into thePress Top Frame (13).
Comments to this Manuals