USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
1015. Attach a Press Arm (7) to one side of thePress Frame (12) with two 5/16” x 2 1/2” Bolts(39) and two 5/16” Nylon Locknuts (40).Attach the other P
1118. Press a 1 3/4” Square Inner Cap (48) into thelower end of the Left Fly Arm (6). Wet thelower end of the Left Fly Arm with soapywater. Slide a 10
1221. Wrap the Butterfly Cable (89) around a 3 1/2”Pulley (82) as shown. Attach the Pulley and aCable Trap (80) to the bracket on the LegPress Upright
1325. Identify the Rear Cable (87)—this is theshortest Cable. Slide one end of the RearCable onto the 5/16” x 3” Bolt (92). Threadanother 5/16” Nylon
1429. Identify the Press Cable (88)—this is thelongest Cable. Attach the end of the PressCable (88) to the Large “U” Bracket (84) witha 1/4” Nylon Loc
1532. Route the Press Cable (88) over the indicated3 1/2” Pulley (82) attached to the PulleyPlates (31). The Cable must be routed fromthe direction sh
1636. Route the Press Cable (88) over the indicated3 1/2” Pulley (82) attached to the PressFrame (12). Be sure that the Cable Trap(80) is turned to ho
1740. Note: The 3 1/2” Pulley (82) used in thisstep was attached in step 38. It is shownremoved for easier part identification.Route the Press Cable (
1844. Locate the remaining preassembled pair ofPulley Plates (31) and 3 1/2” Pulleys (82).Route the High Cable (85) under the indicated31/2” Pulley (8
1948. Wrap the Low Cable (86) around a 3 1/2”Pulley (82). Attach the Pulley and a CableTrap (80) to the Ab Upright (1) with the 3/8” x3 3/4” Bolt (76)
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51. Locate and open the parts bag labeled“SEAT ASSEMBLY.”Attach the Small Backrest (18) to the AbUpright (1) with two 1/4” x 2 1/2” MachineScrews (64)
555657SEAT ASSEMBLYMISC.2158.Make sure that all parts have been properly tightened. The use of the remaining parts will be explainedin HOW TO USE THET
22HOW TO USE THE TRAINING SYSTEMThe instructions below describe how each part of the training system can be adjusted. Refer to the exerciseposter acco
23ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Ab Strap (35) to the Low Cable (86) at theab pulley station with a Cable Clip (33). ATTACHI
24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other n
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately. Thetraining
26CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the High Cable (85), the LowCable (86), the Rear Cable (8
27High Cable (85) Rear Cable (87)Weight Stack—5High Pulley—122331—Top Frame4—Weight Stack4
1/2" x 3/4" Abstandsstück (69)2" Quadratische Innenkappe (56)2" Quadratische Außenkappe(58)1 3/4" Quadratische Innenkappe (48
3/8" Nylonkontermutter (43)5/16" x 1 3/4" Bolzen (68)3/8" x 2" Bolzen (50)5/16" x 2 1/4" Bolzen (62)5/16" x 2
3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautions beforeusing the training system.1. It is
5/16" x 2" Augenbolzen (79)Kabelklammer (33)3/8" x 5" Bolzen (74)3/8" x 3 3/4" Bolzen (76)5/16" x 2 3/4" Schr
PART LIST—Model No. WESY86303 R0100ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
This chart is provided to help you identify the small parts used in assembly. Important: Some parts mayhave been pre-assembled for shipping purposes;
REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL!81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL. SAVE THE PART LIST/EXPLODED DRAWING FOR
123456778910111213141516171819172121222223232424252526262727282829292929303132323334353621218585878631414186878888898956768238422055557650384020564282
345671213141191212222232324242525262627273132323334353621218858783148687888898955032056828043425040694069676740683744403768446740406742508258552055204
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 64 in. Length: 70 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg LeverButter
5ASSEMBLYMake sure you have the following tools:• Two (2) adjustable wrenches• One (1) standard screwdriver• One (1) phillips screwdriver• One (1) rub
1.Locate and open the parts bags labeled“FRAME ASSEMBLY BAG ONE” and“FRAME ASSEMBLY BAG TWO.”Press two 2” Square Outer Caps (58) onto theWeight Base (
4. Slide the Front Seat Frame (8) onto the indi-cated 5/16” x 2 1/2” Carriage Bolts (49) in thePress Base (13). Hand tighten two 5/16”Nylon Locknuts (
8. Lubricate the insides of the holes in the TopWeights (24) as shown. Slide a Top Weightonto each set of Weight Guides (23).9. Attach the Top Frame (
11. Attach the Leg Press Plate (11) to theAdjustment Tube (10) with a 5/16” x 2 1/2”Bolt (39), two 5/16” Washers (20), and a 5/16”Nylon Locknut (40).
Comments to this Manuals