QUESTIONS?As a manufacturer, we are com-mitted to providing completecustomer satisfaction. If you havequestions, or find there are miss-ing or damaged
13. Press two 1” x 2” Inner Caps (83) into theindicated end of the Squat Arm (79).Lubricate a 3/8” x 3 1/4” Bolt (85). Attach theSquat Arm (79) to the
1116. Wrap the High Cable (23) around a “V”-Pulley(6). Attach the “V”-Pulley and a Long CableTrap (50) to the indicated bracket on theFront Upright (4
1220. Route the High Cable (23) around one of the3 1/2” Pulleys (15) attached to the “I” Plates(81). Be sure that the Cable is in thegroove of the Pul
23. Attach the High Cable (23) to a Small “U”-Bracket (67) with a 1/4” Nylon Locknut (2)and a 1/4” Washer (10). Do not completelytighten the Nylon Loc
26. Attach the 3 1/2” Low Pulley (88) and the 5/8”x 9/16” Spacer (73) to the indicated hole inthe Press Frame (17) with a 3/8” x 3 3/4” Bolt(71), and
29. Wrap the Low Cable (86) around a 3 1/2”Pulley (15). Attach the Pulley and a CableTrap (66) to the Press Frame (17) with a 3/8”x 3 1/2” Bolt (16),
33. Route the Low Cable (86) over the lower3.1/2” Pulley (15) attached to the “I”-Plates(81). The Cable must be routed from thedirection shown.34. Sli
37. Wrap the Rear Cable (95) around a 3 1/2”Pulley (15). Attach the Pulley to the bracketon the Stabilizer (5) with a 3/8” x 1 3/4” Bolt(87) and a 3/8
40. Attach the Small Backrest (80) to the RearUpright (56) with two 1/4” x 2 1/2” Screws(43) and two 1/4” Washers (10).41. Press a 1 3/4” Square Inner
1943. Attach the Large Backrest (41) to the FrontUpright (42) with two 1/4” x 2 1/2” Screws(43) and two 1/4” Washers (10). TheBackrest must be oriente
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2045. Press a 1 1/2” Square Inner Cap (32) into theLeg Lever (29).Lubricate the 5/16” x 2 1/4” Bolt (33). Attachthe Leg Lever (29) to the Seat Frame (
21MISC48. Remove the backing from the PRO 9730decal and apply it to the home gym systemas shown.49. Make sure that all parts have been properly tighte
22ADJUSTMENTThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter accompanying this manual
23ATTACHING THE LEG LEVER TO THE LOWPULLEY STATIONTo use the Leg Lever (29), the seat must be attachedto the front upright (see ATTACHING AND REMOV-IN
24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each station. “Top” refers to the 6.5 lb. top weight. Theother numbers
25TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gy
26CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the High Cable (23), the LowCable (86), the Rear Cable (9
27High Cable (23) Press Cable (58)Weight Stack9High Pulley12231Rear Upright3Long “U”Bracket46785
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
WESY97300 R1097APlease Note: The assembly is divided into four stages: 1) frame assembly, 2) press, squat, andbutterfly arm assembly, 3) cable and pul
31. It is the responsibility of the owner to ensurethat all users of the home gym system areadequately informed of all precautions.2. Read all instruc
1/4" Washer (10)–115/16" Washer (8)–113/8" Washer (9)–71/4" x 2 1/2" Screw (43)–53/8" Nylon Locknut (21)–221/4" Nyl
1" Retainer (69)–45/16" x 1 3/4" Bolt (72)–21/2" x 3/4" Spacer (61)–43/8" x 2" Bolt (12)–43/8" x 3 1/2" B
1" Round Inner Cap (49)–61" Round Cover Cap (70)–63/4" Round Inner Cap (34)–45/16" x 2" Eyebolt (35)—11 1/2" Square Inne
81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY97300 R1097AKey No. Qty. Desc
785707070707819192525646426266363102102762367372956737262606061613323277115111188275568278721444449218715212787152120211566123568990278938458104380353
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 34 in. Length: 71 in. Low Pulley StationFoot PlateHigh Pulley StationLat BarLeg LeverButte
5ASSEMBLY22711111578783551511141Before beginning assembly, carefully read thefollowing information and instructions:• Place all parts of the home gym
63. Press a 2” Square Inner Cap (27) into theRear Upright (56).Attach a Rubber Bumper (90) to the RearUpright (56) with a #8 x 1/2” Tap Screw (89).Sli
75. Set two Weight Bumpers (19) onto one of thebrackets on the Stabilizer (5). Insert twoWeight Guides (62) through the WeightBumpers and the bracket
7. Press a 2” Square Inner Cap (27) into eachend of the Top Frame (55). Press a 1 3/4”Square Inner Cap (44) into each end of thecrossbar on the Top Fr
910. Press a 1 3/4” Square Inner Cap (44) into thetop of a Press Arm (46). Press a 1” RoundInner Cap (49) into the side of the Press Arm.Attach the Pr
Comments to this Manuals