USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
1015. Attach a Press Arm (7) to one side of thePress Frame (12) with two 5/16” x 2 1/2” Bolts(39) and two 5/16” Nylon Locknuts (40).Attach the other P
1118. Press a 1 3/4” Square Inner Cap (48) into thelower end of the Left Arm (6). Wet the lowerend of the Left Arm with soapy water. Slide a10” Pad (4
1221. Wrap the Butterfly Cable (89) around a 3 1/2”Pulley (82) as shown. Attach the Pulley and aCable Trap (80) to the bracket on the LegPress Upright
1325. Find the Rear Cable (87)—this is the short-est Cable. Slide one end of the Rear Cableonto the 5/16” x 3” Bolt (92). Thread another5/16” Nylon Ja
1429. Find the Press Cable (88)—this is thelongest Cable. Attach the end of the PressCable (88) to the Large “U” Bracket (84) witha 1/4” Nylon Locknut
1532. Route the Press Cable (88) over the indicated3 1/2” Pulley (82) attached to the PulleyPlates (31). The Cable must be routed fromthe direction sh
1636. Route the Press Cable (88) over the indicated3 1/2” Pulley (82) attached to the PressFrame (12). Be sure that the Cable Trap(80) is turned to ho
1740. Note: The 3 1/2” Pulley (82) used in thisstep was attached in step 38. It is shownremoved for easier part identification.Route the Press Cable (
1844. Locate the remaining preassembled pair ofPulley Plates (31) and 3 1/2” Pulleys (82).Route the High Cable (85) under the indicated3 1/2” Pulley (
1948. Wrap the Low Cable (86) around a 3 1/2”Pulley (82). Attach the Pulley and a CableTrap (80) to the Ab Upright (1) with the 3/8” x3 3/4” Bolt (76)
2TABLE OF CONTENTSLIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51. Locate and open the parts bag labeled“SEAT ASSEMBLY.”Attach the Small Backrest (18) to the AbUpright (1) with two 1/4” x 2 1/2” MachineScrews (64)
555657SEAT ASSEMBLYMISC2158. Make sure that all parts have been properly tightened. The use of the remaining parts will be explainedin HOW TO USE THE
22HOW TO USE THE HOME GYM SYSTEMThe instructions below describe how each part of the home gym system can be adjusted. Refer to the exerciseposter acco
23ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Ab Strap (35) to the Low Cable (86) at theab pulley station with a Cable Clip (33). ATTACHI
24WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 6.5 lb. top weight.The other n
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. Thehome gym
26CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the High Cable (85), the LowCable (86), the Rear Cable (8
27High Cable (85) Rear Cable (87)Weight Stack—5High Pulley—122331—Top Frame4—Weight Stack4
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
WESY86300 R0697BPlease Note: The assembly is divided into four stages: 1) frameassembly, 2) press and butterfly arm assembly, 3) cable and pulleyassem
3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precautions beforeusing the home gym system.1. It is
3/8" Nylon Jam Nut (43)–45/16" x 1 3/4" Bolt (68)–23/8" x 2" Bolt (50)–135/16" x 2 1/4" Bolt (62)–15/16" x 2 1
5/16" x 2" Eyebolt (79)—1Cable Clip (33)–43/8" x 4 1/2" Bolt (74)–13/8" x 3 3/4" Bolt (76)–15/16" x 2 3/4" Car
2" Square Inner Cap (56)–82" Square Outer Cap (58)–21 3/4" Square Inner Cap (48)–71" Retainer (45)–41" Round Outer Cap (46)–2
81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL. SAVE THE PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE.
PART LIST—Model No. WESY86300 R0697BNote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
123456778910111213141516171819172121222223232424252526262727282829292929303132323334353621218585878631414186878888898956668238422055556650384020564282
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 78 in.Width: 64 in. Length: 70 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg LeverButter
5ASSEMBLY156585855204940491. Before beginning assembly, be sure thatyou have read and understand the infor-mation in the box above.Locate and open the
2. Slide the Ab Upright (1) onto the indicated5/16” x 2 1/2” Carriage Bolts (49) in theWeight Base (14). Hand tighten two 5/16”Nylon Locknuts (40) ont
5. Insert two Weight Guides (23) into one of thebrackets on the Weight Base (14). Attach thelower ends of the Weight Guides with a 5/16”x 6” Bolt (67)
8. Lubricate the insides of the holes in the TopWeights (24) as shown. Slide a Top Weightonto each set of Weight Guides (23).9. Attach the Top Frame (
11. Attach the Leg Press Plate (11) to theAdjustment Tube (10) with a 5/16” x 2 1/2”Bolt (39), two 5/16” Washers (20), and a 5/16”Nylon Locknut (40).
Comments to this Manuals