Weider WESY9930 User Manual

®USER’S MANUALModel No. WESY99300Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRe

14. Open the parts bag labelled “CABLE ASSEMBLYAND PULLEYS.” For cable identification and routingduring steps 14–32, refer to the CABLE DIAGRAMSand CA

1115. Wrap the Short Cable (71) over a “V” Pulley (21) asshown. Attach the “V” Pulley and a Long Cable Trap(14) to one side of the welded bracket on t

1220. Attach the threaded shaft on the Medium Cable (72)to the Small “U”-Bracket (43) with a 1/4” Flat Washer(11) and a 1/4” Nylon Locknut (16). Note:

1324. Wrap the Long Cable (73) around a 3 1/2” Pulley (5).Attach the Pulley and a Cable Trap (39) to the indicat-ed bracket on the Butterfly Base (61)

1426. Wrap the Long Cable (73) around a 3 1/2” Pulley (5)in the direction shown. Attach the Pulley and a CableTrap (39) to the indicated bracket on th

1529. Wrap the Long Cable (73) around a “V” Pulley (21) inthe direction shown. Attach the “V” Pulley and a LongCable Trap (14) to the small tube on th

16Seat Assembly34. Press four 3/4” Round Inner Caps (40) into the endsof the Pad Tubes (48).Insert the Pad Tubes (48) into the indicated holes inthe L

1736. Insert a 1/4” x 1 1/2” Carriage Bolt (82) into the centerhole in a Seat Plate (42). Attach the Seat Plate to aSeat (51) with two 1/4” x 3/4” Scr

1839. Apply the WEIDER PRO 9930 decal in the locationshown. 40. Make sure that all parts have been properly tightened. The use of the remaining parts

19CABLE DIAGRAMSThe cable diagrams below and on the next page show the proper routing of the Short Cable (71), the MediumCable (72), and the Long Cabl

2LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20Long Cable (73)12345678913111210

21USING THE CURL PADTo use the Curl Pad (69), insert the Curl Post (70) into theSeat Brace (75) and secure the Curl Post at the desiredheight with the

22Slack can be removed from the Long Cable (73) by relo-cating the indicated 3 1/2” Pulley (5) on the Press SeatFrame (52). To do this, remove the 3/8

23High Arm Butterfly Curl/ Leg RaiseWeight Pulley Press (lbs.) Low Pulley (lbs.)Plates (lbs.) (lbs.) (lbs.)Top 11 20 15 16 171 25 39 31 32 372 40 59

Part No. 173978 R0501A Printed in Canada © 2001 ICON Health & Fitness, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our C

Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable and pulleyassembly; and 4) seat assembly. The hardware for ea

1/4" Flat Washer (11)5/16" Flat Washer (19)3/8" Flat Washer (17)5/16" x 1 3/4" Bolt (9)3/8" Nylon Locknut (4)3/8" J

1" Retainer (25)3/8" x 2" Bolt (35)3/8" x 3 1/2" Bolt (24)3/8" x 2 1/2" Bolt (6)3/8" x 3 3/4" Bolt (7)3/8

1" Round Inner Cap (41)1" Round Cap (26)3/4" Round Inner Cap (40)1 1/2" Square Inner Cap (79)1" Inner Cap (80)1 3/4" Squ

81REMOVE THIS PART LIST/EXPLODEDDRAWING FROM THE MANUAL

3IMPORTANT PRECAUTIONSWARNING: To reduce the risk of serious injury, read the following important precau-tions before using the weight system.1. Read

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY99300R0501AKey No. Qty. Descr

651370372526663765671818712526371871681527186951824213452228811161920742238734139535161395744395352241739535624552236262114383841462064238395720194663

4ASSEMBLED DIMENSIONS:Height: 198 cmWidth: 165 cmDepth: 86 cmLow PulleyStationFoot PlatePress ArmBackrestCurl PadAdjustmentKnobButterflyArmsWeightStac

5ASSEMBLYMake sure you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mallet•

61. Before beginning, make sure that you have readand understood the information on page 5.Locate and open the parts bag labelled “FRAMEASSEMBLY.”Pres

73. Place two Weight Bumpers (84) over the indicatedholes in the Butterfly Base (61). Slide the WeightGuides (58) into the indicated holes.Attach the

87. Turn the Seat Brace (75) so the nut is on the sideshown. Attach the Seat Brace to the Butterfly Base(61) with the indicated 5/16” x 2 1/2” Carria

911. Press a 1 1/2” Square Inner Cap (79) into the PressSeat Frame (52). Slide the bracket on the lower end of the Press SeatFrame (52) onto the indic