Weider E2000 User Manual

USERÕS MANUALModel No. WESY92190Serial No. The serial number is found in thelocation shown below. Write theserial number in the space above.CAUTIONRea

Cable Assembly15. Open the parts bag labeled ÒCABLE ASSEMBLYAND PULLEYS.Ó For Cable identification and rout-ing during steps 15Ð30, refer to the Cable

1119. Remove the 1/2Ó Nylon Locknut (68) from the weldedhook on the Top Frame (1). Slide the Pulley Bracket(20) onto the hook and secure it with the N

1222. Remove the 3 1/2Ó Pulley (35) from the pre-assem-bled Adjustment Bracket (84). Wrap the High Cable(2) around the Pulley in the direction shown.

1326. Move to the other side of the unit. Wrap the LowCable (9) around a 3 1/2Ó Pulley (35) in the directionshown. Attach the Pulley to the Front Upri

31. Open the parts bag labeled ÒSEAT ASSEMBLY.ÓAttach the Backrest (41) to the Front Upright (42) withtwo 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó FlatW

1534. Attach the Curl Pad (24) to the Curl Post (10) withtwo 1/4Ó x 3/4Ó Screws (17).Slide the Curl Post (10) onto the Seat Frame (36) soeach of the w

38a.The following instructions are critical to the cor-rect operation of your weight system. If theadjustment is incorrect, it can damage the motor.Ma

38e.See the inset drawing. Loosen the 3/8Ó Plain Nuts(85), and the 3/8Ó x 3Ó Bolt (88) so that the 3/8Ó x 4ÓTap Screw (86) can rotate freely. Note: Th

1841. Make sure that all parts have been properly tight-ened. The use of the remaining parts will beexplained in HOW TO USE THE WEIGHT SYSTEM,beginnin

19Cable DiagramThe Cable Diagram below shows the proper routing of the High Cable (2) and the Low Cable (9). The numbersshow the correct route for eac

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20How to Use the Weight SystemPLUGGING IN THE POWER CORDPlug in the power cord to a 120-volt outlet. Keep thepower cord away from walkways and heated

21ATTACHING THE LAT BAR, ROW BAR, AB STRAP ORHANDLE TO THE LOW, HIGH OR AB PULLEYSTATIONAttach the Lat Bar (76) to the Low Cable (9) with a CableClip

2231636635Additional slack can be removed by using the PulleyPlates (31). The Pulley Plates have several sets of adjust-ment holes. By moving one or b

1" Round Inner Cap (49)1" Round Cover Cap (3)3/4" Round Inner Cap (34)3/8" x 2 1/4" Eyebolt (44)1 1/2" Square Inner Cap

5/16" Nylon Jamnut (91)3/8" Flat Washer (55)5/16" Flat Washer (56)3/8" Nylon Locknut (57)3/8" Nylon Jamnut (63)3/8" Plai

1" Retainer (4)1/4" Flat Washer (90)3/8" x 3Ó Bolt (88)3/8" x 2 1/4" Bolt (65)3/8" x 1 3/4" Bolt (60)3/8" x 3

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. Part ListÑModel No. WESY92190

343430304433283034283034227138173713913329367473754545212134431565715484791158565353185515114528531212167566550663355554290434142241017726727663555666

Ordering Replacement PartsTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6

3WARNING: Before beginning this or any exercise program, consult your physician. This is especiallyimportant for persons over the age of 35 or persons

4ASSEMBLED DIMENSIONS: Height: 77 in.Width: 38 in. Length: 61 in. Low PulleyStationWarningDecal 2Foot PlateRow BarConsoleHigh PulleyStationAb PulleySt

5Note: This introduction will save you moretime than it takes to read it!Identifying PartsTo help you identify the small parts used in assem-bly, we h

61. Before beginning assembly, make sure you haveread and understood the information on page 5.Open the parts bag labeled ÒFRAME ASSEMBLY.ÓPress a 2Ó

74. Press a 2Ó Square Inner Cap (21) into each end ofthe crossbar on the Top Frame (1).Slide two 5/16Ó Flat Washers (56) onto two 5/16Ó x2 3/4Ó Bolts

810. Press a 1 1/2Ó Square Inner Cap (33) into the end ofthe Seat Frame (36). Insert two 5/16Ó x 2 3/4Ó Bolts (67) through theSupport Plate (27) and t

913Lubricate1Bracket47214345Axle434513. Identify the Right Butterfly Arm (48) and the LeftButterfly Arm (47). Note the position of the weldedbracket o