USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if parts aremissi
1014. Press a 2” x 2 1/2” Inner Cap (125) into the ButterflyFrame (47). Attach the tethers on the two “L”-pins(60) to the Butterfly Frame with a #8 x
19.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Locate the VKR High Cable (74), which is 82 1/4”long and has an eyelet on one
1220. Remove the preattached 3 1/2” Pulleys (78 [onlyone is shown]) from the Offset Double “U”-bracket (61).Wrap the VKR High Cable (74) under a 3 1/2
1324. Route the Lat Cable (88) over a 3 1/2” Pulley (78).Slide a plastic Long Cable Trap (102) onto a 3/8” x1 3/4” Bolt (93). Attach the Pulley to the
1428. Wrap the Butterfly Cable (69) over a “V”-pulley (55).Attach the Pulley and a Long Cable Trap (102) tothe indicated bracket on the Butterfly Upri
1533343532. Locate the Leg Lever Cable (75), which is 98 1/2”long and has an eyelet on one end and a thread-ed pin on the other end.Route the eyelet e
1636. Remove the preattached 3 1/2” Pulley (notshown) from the “U”-bracket (64).Attach the end of the Leg Lever Cable (75) to the“U”-bracket (64) with
1740. Wrap the VKR Low Cable (72) under a 3 1/2”Pulley (78). Attach the Pulley to the indicated brack-et on the Long Base (120) with a 3/8” x 1 3/4” B
1844. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley(78). Attach the Pulley and a Cable Trap (68)between the lower set of holes in the “U”-bracket(6
1948. Wrap the Squat Cable (73) under a 3 1/2” Pulley(78). Attach the Pulley and a Cable Trap to the sec-ond set of holes from the top in the indicate
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2052. Press two 3/4” x 1 1/2” Inner Caps (116) and a 1 1/4”Square Inner Cap (117) into the Seat Bracket (11). Attach the Seat (16) to the Seat Bracket
21565758114114121756. Attach the Squat Arm (32) to the Squat Bracket (37)with two 3/8” x 2 1/2” Carriage Bolts (106), two 3/8”Washers (91), and two 3/
22ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t
23ADJUSTING THE SQUAT ARM, SEAT, ORBUTTERFLY BACKRESTTo adjust the height of the Squat Arm (32), first turnthe Adjustment Handle (65) on the Squat Bra
24WEIGHT RESISTANCE CHARTThe chart below shows the approximate weight resistance at each weight station. “Top” refers to the 10-poundtop weight. The o
25TROUBLESHOOTING Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immedi-ately. The weight sys
26CABLE DIAGRAMSThe cable identification chart below shows the ends of each cable and the lengths of the cables. The cable dia-grams on this page and
27Leg LeverCable (75)VKR LowCable (72)1132456792348
Cable Clip (83)3 1/2" Pulley (78)(Not shown to scale)"V" Pulley (55)(Not shown to scale)4 1/2" Pulley (119)(Not shown to scale)3/8
3/8" x 2" Bolt (100)3/8" x 1 3/4" Bolt (93)#10 x 1" Screw (14)3/8" x 2 1/2" Bolt (18)5/16" x 2 3/4" Bolt
IMPORTANT PRECAUTIONS31. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibil
1 1/4" Square Inner Cap (117)1" Round Inner Cap (29)1 1/2" x 2” Inner Cap (212" Square Inner Cap (105)1 1/2" Square Inner Cap
PART LIST—Model No. WESY38322 R1102BNote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. 1 2 1/2” Washer2
465732891011121315161710910919192020212120202022212324252627272829292836363636303132333311111111111135373839394040404242434346474544454448484950501141
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday, 6
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 77 in.Width: 81 in. Length: 59 in. Squat Knee RestLow Pulley StationLat BarVKR* Arm*Vertical Knee Raise
5ASSEMBLYMake sure that you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mal
1.Locate and open the parts bags labeled “FRAMEASSEMBLY 1” and “FRAME ASSEMBLY 2.”Press a 2” Square Inner Cap (105) into the openend of the Long Base
4. Press a 1 1/2” Square Inner Cap (67) into theButterfly Frame Stop (126).Attach the Butterfly Frame Stop (126) to theButterfly Upright (3) with two
87. Press a 2” x 3” Inner Cap (58) into the top of theSquat Upright (4). Slide the Squat Upright onto thetwo indicated 5/16” x 2 1/2” Carriage Bolts (
99. Slide the Squat Slider (38) down onto the SquatUpright (4).10. Insert the ends of two Weight Guides (42) into theindicated bracket on the Long Bas
Comments to this Manuals